EasyManuals Logo

Citizen CLP-621 Technical Manual

Citizen CLP-621
217 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #36 background imageLoading...
Page #36 background image
2-2. Operation of Control Parts
CLP-621 & CLP-631 2-24
(3-3) Tension Sensor F/R
The Tension Sensor F is used to detect the ribbon tension on the take-up side (front side)
as well as ribbon running. While, the Tension Sensor R is used to detect the ribbon tension
on the supply side (rear side) as well as the ribbon end. These sensors are
photointerrupters.
Tension Sensor F:
The Tension Sensor F is used to keep the ribbon tension on the take-up side constant.
When printing starts, ribbon is fed and take-up side ribbon slacks. Then, the claw of the
Ribbon Tension Shaft F SA comes off the photointerrupter on the Tension Sensor PCB and
the photointerrupter turns ON. Thus, pin 97 (SENS_A) of IC11 (Custom IC) goes "High"
level. Then, IC1 (CPU) drives the Ribbon Motor F to take up ribbon. As a result, ribbon
tightens and the claw is inserted into the photointerrupter. Thus, pin 97 (SENS_A) of IC11
(Custom IC) goes "Low" level. Then, IC1 (CPU) stops the Ribbon Motor F. During printing,
this cycle is repeated and constant ribbon tension is maintained.
The LED (D901) on the tension sensor lights when ribbon slacks (the claw of the Ribbon
Tension Shaft F SA comes off the photointerrupter and the photointerrupter turns ON). The
LED goes out when ribbon tightens.
If ribbon is not correctly fed during printing, the ON/OFF state of the photointerrupter on
the Tension Sensor F becomes improper. Thus, the CPU can detect a ribbon running error.
Tension Sensor R:
The Tension Sensor R is used to keep the ribbon tension on the supply side constant.
When printing starts, ribbon is fed and supply side ribbon tightens. Then, the claw of the
Ribbon Tension Shaft R SA is inserted into the photointerrupter on the Tension Sensor
PCB and the photointerrupter turns OFF. Thus, pin 98 (SENS_B) of IC11 (Custom IC) goes
"Low" level. Then, IC1 (CPU) drives the Ribbon Motor R to supply ribbon. As a result,
ribbon slacks and the claw comes off the photointerrupter. Thus, pin 98 (SENS_B) of IC11
(Custom IC) goes "High" level. Then, IC1 (CPU) stops the Ribbon Motor R. During printing,
this cycle is repeated and constant ribbon tension is maintained.
In the same way as for Tension Sensor F, the LED (D901) on the tension sensor lights
when ribbon slacks and goes out when ribbon tightens.
When ribbon runs out, the ON/OFF state of the photointerrupter on the Tension Sensor R
becomes unchangeable. Thus, the CPU can detect the ribbon end.

Other manuals for Citizen CLP-621

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Citizen CLP-621 and is the answer not in the manual?

Citizen CLP-621 Specifications

General IconGeneral
USB portNo
RS-232 interfaceYes
Optional connectivityEthernet
USB 1.1 ports quantity1
USB 2.0 ports quantity0
Connectivity technologyWired
Flash memory2 MB
CertificationUL, C-UL, FCC class A, CCC, CE Marking
Internal memory8 MB
Number of fonts2
Built-in barcodesPDF417, UPC-A, UPC-E
Built-in processor32 Bit RISC
Mean cycles between failures (MCBF)1000
Power consumption2400 mA
Power requirements100 - 240V, 50 / 60Hz
Compatible operating systemsWindows 2000, XP, Vista
Core diameter25.4 mm
Ribbon length360 m
Media thickness0.0635 - 0.254 mm
Maximum label length812 m
Maximum roll diameter127 mm
Supported paper width19.5 - 118 mm
Weight and Dimensions IconWeight and Dimensions
Depth114 mm
Width91 mm
Height104 mm

Related product manuals