How to fix volume too low or loud on Code Blue Security System amp?
To address low or loud volume on your Code Blue Security System's amplifier, first adjust the volume within the IA4100/IP5000 programming. For IA4100, use in-call commands 28 to increase and 29 to decrease volume. For IP5000, modify the Public Address Gain under hardware settings. Additionally, manually adjust the input gain on the amplifier using the input gain dial.
What to do if there is no power to Code Blue Security System unit?
If your Code Blue Security System unit has no power, check the following: * For CB 1 or 5 units, ensure 120V AC is reaching the transformer. * For CB 2-e units, confirm either Hi-Voltage to the power brick or 24V AC to the unit if it's a low voltage setup. * For WM-180° units, verify 24V AC is supplied to the unit.
What to do if strobes are not working on Code Blue Security System?
To troubleshoot non-working strobes on your Code Blue Security System, check the 5 amp slow blow inline fuse located between the transformer and the 5-finger manifold. Also, inspect the power connector at the 5-finger manifold and the red/black power wire from the strobe. To test the strobe's functionality, short the yellow relay wires from the strobe. If the strobe flashes, verify the programming in the IA4100/IP5000 speakerphone.
How to troubleshoot PAS not working on Code Blue Security System?
If the PAS (Public Address System) is not working on your Code Blue Security System, remove the control cable from the amplifier to keep the amp on at all times, and then try a new test call. Also, test the power from the transformer to the amp.
Copyright, reproduction, warranty, and modification disclaimers.
Adherence to standards, phone line requirements, and programming.
Lists the parts included with the unit for installation.
Lists tools required for installing the CB 1-s model with AED.
Lists tools required for installing the CB 1-w model with WindAssist.
Lists part numbers for the CB 1-e model.
Lists part numbers for the CB 1-s with Dual Faceplates.
Lists part numbers for the CB 1-s with AED Housing.
Lists part numbers for additional options for CB 1-e and CB 1-s models.
Specifications for 24V AC components, including current, watts, and kWh.
Specifications for 12V DC components, including current, watts, and kWh.
Max power consumption for special CB models.
Combined specifications for 120V models (9-2013).
Power specifications for multi-tap power bricks.
Power specifications for various AC components.
Combined specifications for 24V AC models with IP5000.
Overview of Blue Alert Mass Notification Software.
Overview of Blue Alert Emergency Management Software.
Description of the ToolVox emergency management platform.
Steps for preparing the foundation for unit installation.
Steps for placing and leveling the unit on anchor bolts.
Instructions for installing the area light on CB 1-s models.
Steps for installing the dome top assembly and connecting wiring.
Grounding instructions and wiring connections for the unit.
Instructions for connecting 120V AC power supply wires.
Instructions for preparing the foundation for unit installation.
Steps for placing and leveling the unit on anchor bolts.
Instructions for preparing the foundation for unit installation.
Steps for placing and leveling the unit on anchor bolts.
Instructions for installing the area light on CB 1-s with AED Housing.
Steps for installing the dome top assembly and connecting wiring.
Instructions for connecting the ground wire.
Instructions for connecting 24V AC power supply wires.
Instructions for connecting 120V AC power supply wires.
Checklist of items required prior to installation.
Instructions for preparing the foundation for unit installation.
Steps for placing and leveling the unit on anchor bolts.
Instructions for installing the solar panel and wind generator.
Instructions for attaching the stainless steel sleeve to the solar panel.
How to position the solar panel based on latitude.
Diagram showing solar panel positioning angles.
Securing the solar panel and ensuring it faces south.
Wiring instructions for the solar panel assembly and unit.
Instructions for installing the unit's batteries.
General instructions for cellular retrofitting.
Specific retrofit instructions for Telular and CallFinder units.
Specific instructions for removing Telular GSM units.
Detailed step-by-step process for removing the CallFinder unit.
Step-by-step guide for installing the GSM-5 module.
Description of the GSM-5 front panel indicators.
Explanation of the cellular signal strength LEDs.
Table detailing RSSI signal strength levels.
Explanation of the GPS location fix indicator.
Details on LED colors and their indications for Power, Cellular, Status.
Interpretation of general status conditions based on LED behavior.
Explanation of the Power (red) LED status and indication.
Explanation of the Status (green) LED status and indication.
Instructions for preparing the foundation, including conduit and grounding.
Steps for setting anchor bolts in the foundation for unit alignment.
Instructions for pulling power and phone lines through conduits.
Lists the tools needed for camera mount installation.
Instructions for retrofitting existing units for camera mount.
Steps for locating and installing the camera mount.
Instructions for installing the camera itself.
Steps for installing the dome top assembly after camera mount.
Emphasizes compliance with wiring codes.
Instructions for pulling power and communication wires.
Steps for connecting the power wires.
Instructions for connecting the phone line.
Procedure for applying power to the unit.
Instructions for preparing the foundation for unit installation.
Steps for placing and leveling the unit on anchor bolts.
Steps for installing the dome top assembly and connecting wiring.
Grounding instructions and wiring connections for the unit.
Caution regarding applying power before other steps are completed.
Emphasizes compliance with wiring codes.
Instructions for pulling power and communication wires.
Instructions for connecting the phone line.
Instructions for installing the optional digital transceiver (Model CB 1).
Instructions for installing the optional digital transceiver.
Connecting phone wires from GSM to IA4100.
Instructions for setting up the GSM card.
Instructions for connecting power wires, including grounding.
Instructions for installing the unit's battery.
Procedure for applying power to the unit.
Checklist of items required prior to installation.
Instructions for preparing the foundation for unit installation.
Steps for placing and leveling the unit on anchor bolts.
Instructions for installing the solar panel and wind generator.
Instructions for mounting and positioning the solar panel.
Instructions for assembling the blades to the blade hub.
Torque specifications for blade and hub assembly.
Steps for mounting the blades to the blade hub.
Wiring instructions for the turbine assembly.
Instructions for mounting the wind generator unit.
Ensuring the nosecone is securely attached.
Pulling wires and connecting them to the battery.
Connecting solar panel wires to the charge controller.
Connecting wind generator wires to the stop switch.
Instructions for installing the unit's batteries.
Placing batteries into the unit's shelves.
Connecting battery wires, including polarity warning.
Instructions for installing the GSM cellular unit.
Instructions for accessing and preparing the SIM card compartment.
Orienting and inserting the SIM card.
Recording IMEI and Serial Number for the cellular carrier.
Connecting the antenna to the GSM unit.
Setting the VOICE/DATA switch on the GSM unit.
Connecting power to the GSM unit.
Connecting the RJ-11 cable to the GSM unit's FXS port.
Mounting the GSM unit behind the phone.
Instructions for mounting the NMO antenna assembly.
Instructions for programming the AED access unit.
Clarifies that instructions apply to S-1000 and S-1050 models only.
Instructions for activating LEDs in different modes.
Details the photocell feature for the S-1050 model.
Specifies the input voltage range for the unit.
Specifies the operating temperature rating.
Details typical power consumption at 25°C.
Instructions for upgrading CB 1-D and CB 1-s units with A-700 LED Area Light.
Advises to read the entire packet for familiarization.
Lists the tools required for component identification and installation.
Diagram illustrating component names and locations.
Lists the parts required for the conversion.
Lists the callouts for components in the upgrade diagram.
Lists the parts required for the upgrade.
Wiring instructions for the LED upgrade.
Initial electrical connection steps for PoE setup.
Securing manifold wires to the PoE+ splitter.
Connecting the DATA cable to the PoE splitter.
Plugging in the Ethernet PoE Cat 5e cable.
Instructions for grounding the PoE splitter and unit.
General installation instructions for blank rings.
Lists the tools needed for blank ring installation.
Step-by-step instructions for installing blank mounting rings.
Information about the power configuration for blank rings.
Instructions for drilling deck holes and preparing the foundation.
Steps for positioning the upper deck plate.
Steps for positioning the lower deck plate.
Instructions for securing lower nuts and preventing tampering.
Instructions for pulling power and phone lines through conduits.
Wiring diagram for lighting units.
Wiring diagram for power source components.
Wiring details for the wire buss.
Wiring diagram for the power brick.
Diagram for supplied modular inter-connect cables.
Wiring diagram for communication connections.
Wiring diagram for lighting units.
Wiring diagram for power source components.
Wiring diagram for communication connections.
Wiring diagram for lighting units.
Wiring diagram for the IA4100 module.
Wiring diagram for the IP5000 module.
Wiring diagram for lighting units.
Wiring diagram for the IA4100 module.
Wiring diagram for the PH75PG transformer.
Wiring diagram for lighting units.
Wiring diagram for the power supply components.
Wiring diagram for the IA4100 module.
Wiring diagram for the IP5000 module.
Wiring diagram for lighting units.
Wiring diagram for the IA4100 module.
Wiring diagram for the IP5000 module.
Wiring diagram for the NightCharge power source.
Wiring diagram for communication connections.
Wiring diagram for the PAS1 G2R1 amplifier.
Wiring diagram for the PAS1 G2R1 speaker array.
Wiring diagram for the IP5000 module.
Wiring diagram for the IA4100 module.
Wiring diagram for the PAS1G2R2 amplifier.
Wiring diagram for the PAS1 G2R2 speaker array.
Wiring diagram for the IP5000 module.
Wiring diagram for the IA4100 module.
Wiring diagram for lighting components.
Wiring diagram for WindAssist components.
Wiring diagram for the solar circuit.
Wiring diagram for the IA4100 module.
Wiring diagram for the IP5000 module.
Diagram for interconnect cables.
Wiring diagram for CB 1-w batteries.
Wiring diagram for the IA4100 module.
Wiring diagram for the IP5000 module.
Diagram for supplied modular inter-connect cables.
Wiring diagram for the step-down transformer.
Wiring diagram for the power brick.
Power source options for NightCharge/Solar.
Wiring diagram for the PAS 1 module.
Wiring diagram for lighting components.
Wiring diagram for the AC to DC converter.
Wiring diagram for optional IP wireless/IP5000.
Wiring diagram for the AED door release circuit.
Wiring diagram for the PAS power supply.
Wiring diagram for the IA4100 module.
Wiring diagram for the IP5000 module.
Wiring diagram for lighting units.
Wiring diagram for the power brick.
Table detailing component fuse ratings.
Wiring diagram for the AED heater.
Wiring diagram for the AED door control.
Wiring diagram for the IA4100 module.
Wiring diagram for the IP5000 module.
Wiring diagram for the primary side of the transformer.
Wiring diagram for the secondary side of the transformer.
Legend for Guard (G) and Technician (T) tasks.
Daily and weekly maintenance tasks.
Monthly and quarterly maintenance tasks.
Biannual maintenance tasks, including inspections.
Annual maintenance tasks, including battery replacement.
Legend for pollutant levels affecting surface care.
Frequency guidelines for surface care.
Information on average component lifespan.
Contact information for system breakdowns.
Contact information for abnormal operation issues.
The main web address for downloading resources.
General| Type | Emergency Phone |
|---|---|
| Model | CB 1 Series |
| Material | Stainless Steel |
| Communication | Analog |
| Weatherproof Rating | IP66 |
| Operating Temperature | -40°C to +60°C |
To Next Page
