Danfoss AK-CC55 Compact - Light;Blinds;Cleaning Control

Function
Description
Values
Code
Short name
Rail heat control
mode
The rail heat can be controlled in several ways: 0: Rail-
heat is running all the time 1: Pulse control is used
with a timer function following the day/night opera-
tion 2: Pulse control is used with a dew point function.
This function requires that a signal is received about
the dew point value. The value is measured by a sys-
tem manager and sent to the controller via the data
communication.
0=ON, 1=Day/Night timer, 2=Dew point ctrl.
o85
o85 Railh. mode
Rail heat ON cycle
day
Railheat power during day time. The ON period is set
as a percentage of the period
o41
o41 Railh.ONday%
Rail heat ON cycle
night
Railheat power during night time. The ON period is
set as a percentage of the period time
o42
o42 Railh.ONngt%
Rail heat period
time
Periodtime for pulsing of railheat
o43
o43 Railh.cycle
Rail heat PWM - Peri-
od time
Period time for the pulse width modulation
P82
P82 RailCyclePWM
Rail heat min ON cy-
cle
Lowest permitted rail heat power. When the meas-
ured dew point is below the dened minimum limit
the rail heat will run with the set minimum power
o88
o88 Rail Min ON%
Dewpoint min limit
If the measuered dew point is below the set value the
rail heat is running at minimum heat
o86
o86 DewP Min lim
Dewpoint max limit
If the measured dew point is above the set value the
rail heat is maximum
o87
o87 DewP Max lim
Light/Blinds/Cleaning control
Table 33: Light/Blinds/Cleaning control
Function
Description
Values
Code
Short name
Control state A
Readout of the actual control state of the controller
0=Normal ctrl., 1=Hold after defrost, 2=Min ON timer,
3=Min OFF timer, 4=Drip o, 10=Main switch OFF,
11=Thermostat cut-out, 12=Frost protection S4,
14=Defrost, 15=Fan delay, 16=Forced closing,
17=Door open, 18=Melt period, 19=Modulating
temp. control, 20=Emergency control, 23=Adaptive
superheat control, 24=Start injection, 25=Manual
control, 26=No refrigerant selected, 29=Case clean-
ing, 30=Forced cooling, 31=Door open, 32=Power-up
delay, 33=Air heating, 45=Shut down controller,
48=Adaptive liquid control
u00
u00 Ctrl. state
Night condition
Status at the day-/night operation (night operation:
on/o)
0=OFF, 1=ON
u13
u13 Night Cond.
Light
Actual status of output function
0=OFF, 1=ON
u63
u63 Light relay
Blinds
Actual status of output function
0=OFF, 1=ON
u82
u82 Blinds relay
Light control mode
Conguration of light function1: Light is controlled
via day/night status 2: Light is controlled via data
communication and master control parameter "MC
Light signal" 3: Light is controlled by door contact on
DI input. When the door is opened the relay will cut
in. When the door is closed again there will be a time
delay of two minutes before the light is switched o.
4: As "2" but if there are any 15-minute network errors,
the light will switch on and the night blind will open.
5: Light is controlled via DI input signal
1=Day and night, 2=Network, 3=Door switch, 4=Net-
work (Fallback), 5=Digital input
o38
o38 Light cong
Light at Main switch
OFF
Dene how light and blinds are to be controlled at
Main switch OFF 0: Light is switched o and night
blinds are open when the main switch is o 1: Light
and night blinds are independent of main switch.
0=OFF, 1=Normal ctrl.
o98
o98 Light MS=O
Blinds max open
time
Time delay from when blinds have been opened
manually until they close again
P60
P60 BlindOpenTim
Case cleaning mode
The status of the function can be followed here or the
function can be started manually.0 = Normal opera-
tion (no cleaning) 1 = Only fans are running to defrost
the evaporator. All other outputs are O. 2 = Cleaning
with stopped fans. All outputs are O. If the function
is controlled by a digital input signal, the relevant sta-
tus can be seen here in the menu.
0=OFF, 1=Fans run, 2=Cleaning
o46
o46 Case clean
© Danfoss | Climate Solutions | 2022.08 BC365212986197en-000201 | 53
AK-CC55 Compact