Why is my Delta Servo Drives showing a reverse limit error?
A reverse limit error on your Delta Servo Drives can occur because: * The reverse limit switch is activated: Enable the reverse limit switch. * The servo system is unstable: Re-adjust the parameter or evaluate the motor capacity.
What does 'Forward Limit Error' mean on Delta ASD-A2-3043 Servo Drives?
A forward limit error on Delta Servo Drives indicates: * The forward limit switch is activated: Enable the forward limit switch. * The servo system is unstable: Re-adjust the parameter or evaluate the motor capacity.
What to do if Delta ASD-A2-3043 Servo Drives show The internal of the encoder is in error?
If your Delta Servo Drives are showing that the internal of the encoder is in error: * The internal of the encoder is in error. (The internal memory and the internal counter are in error): If issue persists, please send the drive back to the distributors or contact with Delta. * When power on, the motor operates because of mechanical inertia or other causes: When power on, please make sure the motor shaft stands still and will not operate.
What causes abnormal EEPROM in Delta ASD-A2-3043?
If your Delta Servo Drives are showing an abnormal EEPROM: * It is in error when DSP accesses EEPROM: The fault occurs when applying to the power. It means one of the parameters is over the reasonable range. Please re-power on after adjusting. The fault occurs in normal operation. It means it is in error when writing the parameter. The alarm can be cleared by DI.ARST. * Abnormal hidden parameter: Please set the correct type of the drive. * Data in ROM is damaged: Please send the drive back to the distributors or contact with Delta.
What causes Abnormal Signal Output in Delta ASD-A2-3043 Servo Drives?
If your Delta Servo Drives are showing abnormal signal output: * The encoder is in error and cause the abnormal signal output: Conduct the corrective actions of AL.011, AL.024, AL.025, AL.026. * The output pulse exceeds the hardware allowable range: Correctly set parameter P1-76 and P1-46.
How to troubleshoot serial communication error in Delta ASD-A2-3043?
If you're experiencing a serial communication error with your Delta Servo Drives, check the following: * Improper setting of the communication parameter: Correctly set the parameter value. * Incorrect communication address: Correctly set the communication address. * Incorrect communication value: Correctly set the value.
What to do if Delta ASD-A2-3043 Servo Drives show Encoder voltage error or the internal of the encoder is in error?
If your Delta Servo Drives are showing encoder voltage error or the internal of the encoder is in error: * Battery voltage is too high: According to the procedure of Over voltage to check. When corrective actions are done, AL.028 will be cleared automatically. * The internal encoder is in error: If the situation is not improving, please send the drive back to the distributors or contact with Delta.
What causes serial communication time out in Delta ASD-A2-3043?
A serial communication timeout error in Delta Servo Drives can occur due to: * Improper setting of the time-out parameter: Correctly set the value. * The drive hasn’t received the communication command for a long time: Correct wiring.
What does main circuit power lack phase mean for Delta Servo Drives?
If your Delta Servo Drives are showing main circuit power lack phase, the main circuit power is abnormal. Make sure it applies to the power. If issue persists, please send the drive back to the distributors or contact with Delta.
How to fix incorrect wiring of the motor power line U, V, W in Delta ASD-A2-3043?
If your Delta Servo Drives are showing incorrect wiring of the motor power line U, V, W because the wiring of U, V, W of the motor is incorrectly connected or the connection is breakdown, follow the user manual to correctly wire U, V, and W and make sure it is grounded.
General| Model | ASD-A2-3043 Series |
|---|---|
| Series | ASD-A2 |
| Category | Servo Drives |
| Output Power | 3.0 kW |
| Control Modes | Position, Speed, Torque |
| Communication Interface | RS-485, CANopen |
| Protection Class | IP20 |
| Operating Temperature | 0°C to 55°C |
| Storage Temperature | -20°C to 65°C |
| Weight | 3.5 kg |
| Power Supply | 3-phase 200-230VAC, 50/60Hz |
| Feedback System | Incremental Encoder |
| Protection Features | Overload, Overvoltage, Overtemperature |
| Humidity | 20% to 90% RH (non-condensing) |
| Vibration Resistance | 5.9 m/s² |
| Shock Resistance | 19.6 m/s² |
Specifies environmental requirements for servo drive and motor installation for optimal reliability.
Details correct mounting orientation and required clearance for ventilation to prevent malfunction.
Provides wiring information for connecting peripheral devices to the 220V series servo drives.
Details the terminal signals, names, and descriptions for connecting motors and regenerative resistors.
Explains the wiring methods for single-phase and three-phase power supplies for 220V servo drives.
Provides wiring information for connecting peripheral devices to the 400V series servo drives.
Details terminal signals, names, and descriptions for 400V series servo drives.
Explains the wiring methods for 400V servo drives, covering three-phase power supply.
Illustrates basic wiring diagrams for 220V series servo drives, including models with and without regenerative resistors.
Illustrates basic wiring diagrams for 400V series servo drives, covering models with and without regenerative resistors.
Details the CN1 connector's terminal layout for I/O signals, including digital and analog inputs/outputs.
Provides pin diagrams for the CN1 connector, showing digital, analog, and encoder signals.
Explains the function and wiring method for various signals connected to the CN1 connector.
Illustrates wiring diagrams for analog and pulse inputs, as well as digital outputs for CN1.
Details the CN5 connector for connecting external linear scales or encoders for full-closed loop control.
Provides standard wiring diagrams for 220V series servo drives in various control modes.
Illustrates the standard wiring for Position (PT) control mode with 220V series servo drives.
Illustrates the standard wiring for Position (PR) control mode with 220V series servo drives.
Illustrates the standard wiring for Speed Control Mode with 220V series servo drives.
Illustrates the standard wiring for Torque Control Mode with 220V series servo drives.
Provides standard wiring diagrams for 400V series servo drives in various control modes.
Illustrates the standard wiring for Position (PT) control mode with 400V series servo drives.
Illustrates the standard wiring for Position (PR) control mode with 400V series servo drives.
Illustrates the standard wiring for Speed Control Mode with 400V series servo drives.
Illustrates the standard wiring for Torque Control Mode with 400V series servo drives.
Describes the functions of the display, SHIFT, SET, DOWN, MODE, UP keys, and Charge LED.
Details the procedure for switching between modes and operating within each mode.
Guides through pre-operation checks like appearance, wiring, and component integrity before applying power.
Provides step-by-step instructions for correctly wiring and powering on the servo drive.
Explains how to perform a JOG trial run without load using software or DI control for testing.
Details the procedure for trial run in speed control mode, including digital input settings.
Outlines the procedure for trial run in position control mode, including digital input settings.
Provides procedures for estimating inertia ratio using JOG mode and performing auto/semi-auto tuning.
Visualizes the step-by-step process for tuning the servo system.
Illustrates the process of estimating inertia ratio, including checks for mechanical vibration.
Details the automatic tuning process, including inertia estimation and stiffness/bandwidth settings.
Lists servo drive alarms with descriptions, corresponding DO signals, and servo status.
Details CANopen communication alarms, their descriptions, and corrective actions.
Lists motion control alarms including loading errors, parameter range issues, and PR command overflows.
Provides causes and corrective actions for common servo drive alarms like Over current, Over voltage, and Under voltage.
Lists corrective actions for various alarms, including turning DI.ARST on or re-powering the servo.
Lists alarms related to absolute systems, including encoder voltage errors, gray code errors, and position loss.
To Next Page
