ENGLISH
I
Troubleshooting
If
a
problem
should
arise,
first
check
the
following:
1.
Are
the
connections
correct?
2.
Is
the
set
being
operated as described in
the
owner's
manual?
3.
Are
the
other
components
operating
properly?
If this unit does not operate properly, check the items listed
in
the table below. Should the problem persist,
there may be a malfunction.
In
this case, disconnect the power immediately and contact your store
of
purchase.
[General]
Symptom
Cause Countermeasure Page
Power does not
• Connection of the power cord
is
• Check the insertion
of
the power
17
turn on, or turns
faulty. cord plug.
off directly after it
was turned on.
No sound
is
• Connection with the input
• Check the connections. 9 -
17
produced from
devices or connection
of
the
speakers.
speaker cables
is
faulty.
• Device you want to play
and
set
• Select
an
appropriate input 35
input source do not match. source.
• Master
volume
is
turned too
• Adjust the master volume to
an
35
low.
appropriate level.
•
Mute
mode
is
set. • Cancel the
mute
mode.
36
• Headphones
are
connected. • Disconnect the headphones. 36
• No
digital signals are being
• Select
an
input source for which
25
input. the digital input setting
has
been
made.
• The
connectors
to
which the
• Set the input mode.
35
digital inputs
are
assigned and
the settable input modes do not
match.
Display
is
off.
• The
"Dimmer"
setting
is
set to
• Set
to something other than 36
"OFF': "OFF':
"DOLBY
DIGITAL:'
•
DVD
player's digital audio output • Check the
DVD
player's audio
-
indicator does not
setting
is
not proper. output setting.
For
details, read
appear
on
display.
the
DVD
player's operating
instructions.
57
Symptom
Cause Countermeasure
Page
Power turns off
• Protection circuit activated due
•
Turn
off the power, wait for the
9
suddenly
and
to rise
of
internal temperature. set to fully cool down, then turn
power indicator the power back on.
flashes
red.
• Place the set in a well-ventilated 3
place.
• Core wires
of
two
speakers
are
• First
unplug the power cord, 9
touching each other or a core then
twist
the core wires tightly
wire
is
sticking out of the terminal or terminate the speaker cables,
and touching the set's rear panel, then reconnect.
activating the protection circuit.
• Speakers
with
an
impedance • Use speakers
with
the specified
9
other than specified are being impedance.
used.
• Set
is
damaged.
•
Turn
off the power
and
contact a
-
DENON service center.
[Remote Control
Unit]
Symptom
Cause Countermeasure
Page
Set does not work
• Batteries are worn.
• Replace with
new
batteries.
3
properly when
•
You
are operating outside of the
• Operate
within the specified 3
remote control specified range.
range
unit operated.
• Obstacle between main unit
and
• Remove the obstacle:
3
remote control unit.
•
The
batteries are not inserted
in
• Insert
the batteries
in
the 3
the proper direction,
as
indicated proper direction, following the
by the polarity marks
in
the
polarity marks
in
the battery
battery compartment.
compartment.
•
The
set's remote control sensor • Move the set to a place
in
which
3
is
exposed
to
strong light (direct the remote control sensor will
sunlight, invertertype fluorescent
not
be
exposed to strong light.
bulb light. etc.).
•
The
remote
ID
of
the main unit
• Set "Remote
ID"
for the main
29
and remote control unit do not
unit to "1':
match.
To Next Page
Loading...
