To Next PageTo Next PageHow to fix reception fails, or there is a lot of noise or distortion on Denon Stereo Receiver?
Change the antenna orientation or position. Separate the AM loop antenna from the unit. Use an FM outdoor antenna. Ensure the antenna is separated from other connection cables.
Why is there no audio output from my Denon AVR-4311 Stereo Receiver?
If there's no audio, verify all device connections, speaker connections, and configurations. Ensure the audio device is powered on, the master volume is adjusted appropriately, and mute mode is off. Select a suitable input source and mode, and disconnect any headphones.
Why is my Denon AVR-4311 Stereo Receiver display off?
Set 'Dimmer' on the menu to something other than 'OFF'.
What does it mean when the power indicator is blinking red on my Denon AVR-4311 Stereo Receiver?
If the power indicator is blinking red in intervals of approximately 0.5 seconds, use speakers which have the specified impedance. Also, the speaker cable might be shorted (touching). Firmly twist the core wire in the speaker cable, and then re-connect it to the speaker terminal. If the power indicator is blinking red in intervals of approximately 2 seconds, the temperature inside the unit has risen. Turn off the power and re-apply it after the temperature has fallen sufficiently. Re-install this unit in a place having good ventilation.
What to do if there is no video output with HDMI connection on my Denon AVR-4311 Stereo Receiver?
Check the connection of the HDMI connectors. Ensure the input source matches the connected HDMI connector. Verify that the TV is compatible with copyright protection (HDCP). If connected to a device not compatible with HDCP, video will not be output correctly.
What to do if my Denon Stereo Receiver power does not turn on?
First, check if the power plug is correctly inserted into the power outlet. If it is, the protection circuit might be active. Disconnect the power plug, wait 5 to 10 seconds, and then reinsert it.
Why can't internet radio be played on my Denon Stereo Receiver?
The Ethernet cable is not properly connected, or the network is disconnected. The program is being broadcast in a non-compatible format. The computer's or router's firewall is activated. The radio station is not currently broadcasting. The IP address is wrong.
Why is there no sound from front height speaker on my Denon AVR-4311 Stereo Receiver?
Set 'Surround Parameters' – 'PLgz Height' on the menu to 'ON'. Check if 'Amp Assign' is set appropriately to output audio from the front height speakers. Set 'Speaker Config.' – 'Front Height' on the menu to something other than 'None'.
Why is there no sound from surround back speaker on my Denon AVR-4311?
Check if 'Amp Assign' is set appropriately to output audio from the surround back speakers. Set 'Speaker Config.' – 'Surround Back' on the menu to something other than 'None'. Set 'Surround Parameters' – 'Surround Back' on the menu to something other than 'OFF'. Ensure the surround mode is not set to 'STEREO'.
How to fix no audio output with HDMI connection on Denon AVR-4311 Stereo Receiver?
Check the connection of the HDMI connectors. When outputting HDMI audio from the speakers, set 'HDMI Audio Out' on the menu to 'AMP'. When outputting HDMI audio from a TV, set 'HDMI Audio Out' on the menu to 'TV'.
General| Type | AV Receiver |
|---|---|
| Number of channels | 9.2 |
| Output Power per Channel | 140 W (8 ohms, 20 Hz - 20 kHz, 0.05% THD) |
| Frequency Response | 10 Hz - 100 kHz (+1, -3 dB) |
| Total Harmonic Distortion | 0.05% |
| Input Sensitivity/Impedance | 200 mV / 47 kohms |
| Signal-to-Noise Ratio | 102 dB |
| HDMI outputs | 2 |
| 3D Support | Yes |
| Network features | AirPlay, DLNA |
| Audio DAC | 24-bit/192kHz |
| Video Inputs/Outputs | Component |
| Audio Inputs/Outputs | Analog, Optical, Coaxial |
| Network Connectivity | Ethernet |
| Supported Audio Formats | Dolby TrueHD, DTS-HD Master Audio, FLAC, WAV, MP3, WMA, AAC |
| Dimensions (W x H x D) | 434 x 195 x 427 mm |
| HDMI inputs | 7 (1 on front) |
Guidance on proper placement and ventilation for safe operation and optimal performance.
Lists all items supplied with the product, ensuring you have everything needed for setup.
Highlights the key capabilities and technologies of the audio receiver for enhanced user experience.
Provides essential precautions for safe operation, including power, condensation, and handling guidelines.
Step-by-step instructions for unboxing, connecting, and setting up the receiver for immediate use.
Details how to connect various audio and video devices to the receiver for optimal signal transfer.
Covers fundamental playback procedures for different sources like Blu-ray, CD, iPod, and network audio.
Allows users to choose the optimal sound mode for movies, music, or games for an immersive experience.
Provides detailed instructions for setting up various speaker configurations beyond the basic 7.1 system.
Covers advanced playback features, including convenient functions and zone control for multi-room audio.
Details how to enjoy audio in additional rooms using ZONE2 and ZONE3 outputs for synchronized or independent playback.
Guides users through the menu system for customizing various audio, video, and network settings.
Explains how to use the remote control to operate the receiver and other connected AV equipment.
Identifies and explains the purpose of all buttons and connectors on the front and rear panels of the receiver.
Covers essential details such as trademarks, surround mode compatibility, and explanations of technical terms.
Offers solutions for common operational issues, helping users diagnose and resolve problems with the unit or connections.
Lists the technical specifications of the audio section, tuner, remote controls, and power requirements.
