11
47
48
55
56
57
57
57
58
58
59
60
61
62
63
64
65
64
66
66
67
68
69
49
50
51
52
53
54
55
56
57
57
47
48
49
50
51
52
53
54
47. FX On: Press these buttons to enable or disable FX 1 and FX 2.
48. FX Select: Turn these knobs to select the active effect for FX 1 and FX 2.
49. FX Parameter: When lit, press this button to activate the secondary parameter for an effect. The button will be
unlit for effects that do not have a secondary parameter.
When using effects such as Echo, Hall Echo, and Reverb, this button will trigger an effect hold or freeze. This
allows you to accomplish transition effects such as Echo Out or Reverb Out in a single action without having to
stop the deck or move a fader. The button will flash to indicate when a Hold/Freeze is active.
50. FX Parameter Knob: Use these knobs to adjust the effect parameter.
51. FX Reset: Press these buttons to reset the FX Frequency to center.
Press and hold Shift and press these buttons to set the effect to its default state, with Wet/Dry set to 0.
52. FX Frequency: Turn this knob to select a frequency band of the audio signal to which the BPM effects will be
applied. Select the center (12 o'clock) position to apply effects to the entire spectrum of frequencies.
53. FX Wet/Dry Knob: Turn this knob to adjust the wet/dry mix of the effects.
54. FX Beats Buttons: Press either of these buttons to decrease or increase the rate of time-based effects on that deck.
55. Mic On/Off: Press these buttons to activate/deactivate the microphones.
56. Mic Level: Turn these knobs to adjust the volume levels of the corresponding microphone inputs. The Peak light
next to each knob indicates the current signal level by its color: green (low), amber (normal/optimal), or red
(maximum/peak). You can adjust the microphone attenuation in the Settings menu.
Important: The audio signals from the microphones are routed directly to the Master Outputs.
57. Mic EQ: Turn these knobs to boost or cut the high, mid-range (Mic 1 only) and low frequencies for the
corresponding microphones.
58. Echo On/Off: Press this button to activate/deactivate the echo effect on the microphones’ audio signal.
59. Mic Echo Level: Turn this knob to adjust the amount of the echo effect on the microphones’ audio signal.
60. Talkover: Press this button to use the “talkover” feature, which automatically reduces the volume level of the
master mix when you speak into the microphone. You can adjust the talkover level in the Settings menu.
61. Master Level: Turn this knob to adjust the volume level of the Master Outputs.
62. Zone Channel Assign: Press this button to set Deck 4 as a Zone Playlist, which will play from the Zone
Outputs. By default, the master output will play through the zone if a zone playlist is not assigned.
63. Zone Level: Turn this knob to adjust the volume level of the Zone Outputs.
64. Zone EQ: Turn these knobs to boost or cut the high and low frequencies for the Zone Outputs.
65. Booth Level: Turn this knob to adjust the volume level of the Booth Outputs.
66. Booth EQ: Turn these knobs to boost or cut the high and low frequencies for the Booth Outputs.
67. SD Card Slot: Insert a standard SD card to this slot. When you select that SD card as a source, you can use the
display to select and load tracks on your SD card.
68. USB 1/2 Ports: Connect standard USB flash drives to these USB ports. When you select that USB flash drive as
a source, you can use the display to select and load tracks on your USB flash drive.
69. Eject: Press this button to bring up on the touchscreen a list of connected media devices which can be ejected.
Tap one of the listed media sources to eject that device. To prevent data corruption, drives must be ejected
before being removed from the player.
Press and hold Shift and press this button to open the Source menu.
To Next Page
