Why does my Dexter Laundry T-650 Washer only tumble in one direction?
If your Dexter Laundry Washer only tumbles in one direction, review the indicator lights displayed on the VFD. Also, inspect the yellow enable wires from the main relay PCB and at the VFD.
Why Dexter Laundry T-650 machine does not start?
If your Dexter Laundry Washer isn't starting, several factors could be at play. Begin by examining the power supply, checking circuit breakers, voltage, power leads, and connections. Ensure the front display LED is lit. Next, verify the door switch for continuity when closed; adjust or replace if necessary. Inspect the control breaker or fuse for continuity and replace if needed. Check the control transformer's voltage output. Ensure all wire connections on the PCB board and relay PCB are secure. Also, confirm that the door lock mechanism is receiving the correct voltage after pressing the start button. Lastly, inspect the data cable phone type connectors between the PCB and VFD, ensuring they are properly plugged in after removing power.
Why does water drain slowly from my Dexter Laundry Washer?
If your Dexter Laundry Washer is draining slowly, check the hoses and drain valve for any blockages. Ensure the drain size is adequate. If necessary, inspect the building drains for blockages.
What to do when my Dexter Laundry Washer starts but does not operate?
If your Dexter Laundry Washer starts but doesn't operate, verify that the yellow enable wires from the relay PCB P13 & motor P14 to the VFD are connected and advancing through the cycle. Check the fault code on the VFD before removing power from the drive. Also, check the orange P-15 wire for a signal from the door switches.
What to do if Dexter Laundry T-650 door does not lock?
If the door on your Dexter Laundry Washer isn't locking, check the display for any fault codes. Specifically, if F1 is displayed, consult the fault code section for further instructions. Verify that the door locking mechanism is receiving the appropriate voltage from the main relay PCB; if it is, consider replacing the mechanism. Also, check the door latch switch for continuity when the door is closed; adjust or replace the switch if there is no continuity.
What to do if no cold water to tub in wash for Dexter Laundry Washer?
If cold water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, check the water valve coil for continuity at its terminals and replace it if there's no continuity. Inspect the water inlet screens for blockages and clean them if necessary. Ensure that the water supply is turned on and operating. Check the black and white wires at the Molex plug on the PCB at the main controller and at the relay PCB. Also, check the pressure switch continuity between terminal contacts; if there's no continuity, inspect the pressure switch hose for obstructions and replace the switch if the hose is clear.
How to fix water leakage around loading door of Dexter Laundry Washer?
If there's water leakage around the loading door of your Dexter Laundry Washer, the door may need adjustment due to wear. Check the tightness around the perimeter using a dollar bill. Adjust left-to-right tightness using shims at the door lock or hinge side. Center the gasket to the tub opening before tightening the door to the hinge bolts. Chalk may be used on the tub front to show the point of contact with the tub. If the gasket is deformed, worn, or damaged, replace it.
Why is there no cold water entering the tub in my Dexter Laundry T-650 during wash?
If no cold water is entering the tub of your Dexter Laundry Washer during the wash cycle, start by checking the water valve coil for continuity at the terminals and replace it if necessary. Inspect the water inlet screens for any blockage and clean them if needed. Ensure that the water supply is turned on and functioning correctly. If the appropriate voltage is not present at the valve, refer to the wiring diagram for your specific washer model. Check for voltage at the P4 Connector on the Relay PCB and for LED indication that the appropriate relay is activated. Check the pressure switch continuity between terminal contacts; if there's no continuity, check the pressure switch hose for obstructions, and if the hose is clear, replace the pressure switch.
How to open a Dexter Laundry Washer door that will not open?
If the door of your Dexter Laundry Washer won't open, check if the thermoactuator and its mechanism are stuck or binding. Ensure the locking thermoactuator is not receiving 24VAC during the last 1 1/2 minutes of the cycle and that the unlocking thermoactuator is receiving 24VAC during the last minute. If the timing and voltage are correct, replace the thermoactuator. Also, verify that the door rod from the mechanism to the lock assembly is long enough to allow the lock assembly to disengage; adjust the rod or the position of the mechanism if needed. Check that the door lock mechanism is not stuck closed; if it is, replace it.
What to do if the door of my Dexter Laundry Washer does not lock?
If the door of your Dexter Laundry Washer isn't locking, first check the display for any error messages and follow the tests described in the fault code section. Then, verify that the door locking mechanism is receiving 120VAC (for 60 Hz models) or 24VAC (for 50 Hz models) from the main relay PCB; if it's receiving power but not functioning, replace the mechanism. Also, check the door switch for continuity through the door latch.
Instructions are for qualified personnel only to avoid injury and electrical shock.
Do not wash loads that may create an explosive atmosphere.
Remove load quickly after cycle completion or power failure to avoid spontaneous combustion.
VFDs have capacitors that stay live for up to 10 minutes after power disconnection.
Use disconnect device to lock out/tag out before servicing. Failure can cause serious injury or death.
Do not operate in any hazardous classified (ATEX) environment.
Covers foundation requirements, anchoring, grouting, floor load data, and mounting details for all models.
Details plumbing requirements, electrical connections, fusing, and surge suppressors.
Covers starting procedures, cycle indicators, stop button functions, and general warnings.
Details error codes, their conditions, delays, actions, and solutions for troubleshooting.
Provides safety guidelines and remedies for common machine issues and faults.
General| Brand | Dexter Laundry |
|---|---|
| Model | T-650 |
| Category | Washer |
| Language | English |
To Next Page
