Digi DC-788 - Item Code Call Up; Recall Numeric Item Code; Recall Alphanumeric Item Code; Review PLU Contents

17
19.9. Item Code Call Up
19.9.1. Recall Numeric Item Code
1 - ZERO 2 - NET 3 - GROSS 4 - INSUFF 5 - IN 6 – OUT
OPERATION
Key-in
TARE WEIGHT U.Weight QTY. 1 2 3 4 5 6
Weighing mode. 0.0 0 0 0.0 0 0 0 0
Enter item code. [1] [0] [0] 1 0 0
Call up item code. [CODE] 0.0 0 0 0.0 0 0 1.6 9 8 0 0
Select “In-Out” status. [IN/OUT] 0.0 0 0 0.0 0 0 1.6 9 8 0 0
Put bulk parts on platter. 0.0 0 0 0.1 4 5 1.6 9 8 0 8 4
[*] 0.0 0 0 0.1 4 5 1.6 9 8 0 8 4
Note: 1) If DC-788 is connected to printer/PC, the data is printed/output by pressing [*] key.
And inventory value will update according to the IN/OUT status and Accumulation when quantity is accumulating.
Subtract from inventory when OUT status. Accumulate inventory when IN status.
19.9.2. Recall Alphanumeric Item Code
1 - ZERO 2 - NET 3 - GROSS 4 - INSUFF 5 - IN 6 – OUT
OPERATION
Key-in
TARE WEIGHT U.Weight QTY. 1 2 3 4 5 6
Weighing mode. 0.0 0 0 0.0 0 0 0 0
ASCII enter mode. [.] A S C 0 1 0 0 0 - CODE
Call up PLU. [8] [0] A S C 0 1 0 8 0 - P CODE
“+” key to move cursor ahead. [+] A S C 0 2 0 0 0 - CODE
“-” key to move cursor back. [-] A S C 0 1 0 8 0 - P CODE
“C” key to delete character. [C] A S C 0 2 0 0 0 - CODE
[6] [5] A S C 0 1 0 6 5 - A CODE
[+] [6] [6] A S C 0 2 0 6 6 - b CODE
Call up item code “ABC10”. [CODE] 0.0 0 0 0.0 0 0 1.6 9 8 0 0
Select “In-Out” status. [IN/OUT] 0.0 0 0 0.0 0 0 1.6 9 8 0 0
Put bulk parts on platter. 0.0 0 0 0.1 4 5 1.6 9 8 0 84
[*] 0.0 0 0 0.1 4 5 1.6 9 8 0 84
Note: 1) If DC-788 is connected to printer/PC, the data is printed/output by pressing [*] key.
And inventory value will update according to the IN/OUT status and Accumulation when quantity is accumulating.
Subtract from inventory when OUT status. Accumulate inventory when IN status.
19.9.3. Review Current PLU Contents
1 - ZERO 2 - NET 3 - GROSS 4 - INSUFF 5 - IN 6 – OUT
OPERATION
Key-in
TARE WEIGHT U.Weight QTY. 1 2 3 4 5 6
Weighing mode. 0.0 0 0 0.0 0 0 0 0
Enter item code. [1] [0] [0] 1 0 0
Call up item code. [CODE] 0.0 0 0 0.0 0 0 1.6 9 8 0 0
Select “In-Out” status. [IN/OUT] 0.0 0 0 0.0 0 0 1.6 9 8 0 0
Put bulk parts on platter. 0.0 0 0 0.1 4 5 1.6 9 8 0 8 4
Review PLU contents[Scale] [Scale] ICODE 100
[Scale] Pno 123A
[Scale] Pname SCREW
[Scale] Lnum 2
[Scale] INVENT 4012
[Scale]
0.0 0 0 0.1 4 5 1.6 9 8 0 8 4
Note: 1) If DC-788 is connected to printer/PC, the data is printed/output by pressing [*] key.