Directed DS4+ - User Manual

62 pages

Save Page as PDF

To Next Page

FORD6

INSTALLATION GUIDE

This product is intended for installation by a professional installer only! Attempts to install this

product by a person other than a trained professional may result in severe damage to a vehicle’s

electrical system and components.

2017-12-13

DS4+

Main Page

Questions and Answers

A
Allison LangSep 13, 2025
Why does my Directed Remote Starter say that speed was detected?
- M
  Michelle SmithSep 13, 2025
  The vehicle was detected as moving, which prevents the Directed Remote Starter system from shutting it down.
J
Joseph HughesSep 13, 2025
What does DEI feature error mean on my Directed Remote Starter?
- K
  Kevin JohnsonSep 13, 2025
  A feature config file mismatch was detected.
R
Robert HoldenSep 13, 2025
What to do if Directed DS4+ Automobile Accessories says CAN1 not detected?
- A
  aholtSep 13, 2025
  If the Directed Automobile Accessories module reports that CAN1 is not detected, check the connections of the CAN1 Tan and Tan/Black wires. You can try to wake up the data bus by turning the ignition on and trying again. If your installation doesn't need this connection, you can skip this step by pressing the programming button 5 times.
M
moralesstephanieSep 14, 2025
What to do if Directed DS4+ says CAN2 not detected?
- J
  Jake CarneySep 14, 2025
  If the Directed Automobile Accessories module reports that CAN2 is not detected, check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
L
Lori VasquezSep 14, 2025
What to do if Directed DS4+ says J1850 not detected?
- B
  Briana DudleySep 14, 2025
  Check the J1850 wire connection for your Directed Automobile Accessories. You might also need to wake up the data bus by turning the ignition on and trying again.
O
Olivia JacksonSep 14, 2025
What to do if Directed DS4+ has bypass processing error?
- K
  Keith FisherSep 14, 2025
  Reset the Directed Automobile Accessories module and try again. If the condition persists, please contact Technical Support.
L
Leslie HubbardSep 14, 2025
What to do if Directed DS4+ Automobile Accessories says ISO 1 not detected?
- A
  Amy HumphreySep 14, 2025
  Refer to “Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections if the Yellow/Black wire of your Directed Automobile Accessories did not detect the expected signal.
T
Tammy HarrisSep 14, 2025
What to do if Directed DS4+ says ISO 2 not detected?
- R
  robert03Sep 14, 2025
  Refer to “Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections if the Orange/Black wire of your Directed Automobile Accessories did not detect the expected signal.
P
Paul CarrollSep 14, 2025
What to do if Directed Automobile Accessories says MUX not detected?
- J
  Jeffrey RothSep 15, 2025
  Refer to “Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections if the Violet/Green or Violet/Brown wire of your Directed Automobile Accessories did not detect the expected voltage value.
B
beardlindaSep 15, 2025
What to do if Directed DS4+ Automobile Accessories has DEI feature error?
- K
  Kevin MyersSep 15, 2025
  Please contact Technical Support if you encounter a DEI feature error with your Directed Automobile Accessories.