DMP Electronics XTLplus SERIES - Disarmed Open; Message To Transmit; Output Number; Output Action

Digital Monitoring Products XTLplus Installation and Programming Guide
36
ZONE INFORMATION
33.11 Disarmed Open
Denes the action taken by the panel when the zone is opened while the area is
disarmed. There are three actions to dene:
• Message to Transmit
• Output Number
• Output Action
You must also make these selections for the Disarmed Short, Armed Open, and
Armed Short zone conditions. Press the COMMAND key to continue.
33.11.1 Message To Transmit
You can send two report types to the receiver: Alarm and Trouble. These are
represented by the characters A and T. Press any select area to display the zone
report options.
ALARM - Selecting A allows an alarm report to be sent to the receiver and the
wireless siren output to activate according to zone type. See the Bell Action
section. The zone name appears in the panel’s alarmed zones status lists.
TROUBLE - Selecting T allows a trouble report to be sent to the receiver and the
zone name to appear in the panel’s alarmed zones status lists.
LOCAL - When you select L, an alarm report is NOT sent to the receiver. The bell
output still activates according to zone type and the zone name appears in the
panel’s alarmed zones status lists.
– (dash) - When you select – , reports are NOT sent to the receiver. The wireless
siren output does not activate and there is no display in the panel’s alarmed zones
status list. Only the programmed Output Number activates.
33.11.2 Output Number
You can specify any of the outputs on the XTLplus to be activated by a zone
condition. The output can be activated regardless of the report to transmit
or whether or not the zone is programmed as local. An output activated by a
non-24-hour armed zone is turned o when the zone’s area is disarmed by a user.
To enter an Output Number, press any select area followed by the output number
51-54, 61-64, or F1-F20. Press the COMMAND key.
33.11.3 Output Action
Entering an Output Number displays this option that allows you to assign an output
action. A description of the available output actions is given below:
STEADY - The output is turned on and remains on until the area is disarmed, an
output cuto time expires, or the output is reset from the keypad User Menu.
PULSE - The output alternates one second on and one second o until the area is
disarmed, an output cuto time expires, or the output is reset from the keypad
User Menu.
MOMENTARY - The output is turned on only once for one second.
FOLLOW - The output is turned on and remains on while the zone is in an o
normal, or bad condition. When the zone restores, the output is turned o.
After you have selected the Message To Transmit, the display prompts you for
the same three selections for Disarmed Short, Armed Open, and Armed Short
conditions. If the zone is a 24-hour type, only the Armed Open and Armed Short
conditions are displayed. When you have programmed all of the zone conditions,
the Swinger Bypass selection is then dis played.
33.12 Swinger Bypass
Selecting YES allows the zone to be swinger bypassed by the panel according to
the programming in Swinger Bypass Trips and Reset Swinger Bypass. The Bypassed
zone displays in the keypad Status List. Selecting NO disables swinger bypassing for
this zone.
How it works
If within one hour, a zone trips the total number of times as specied in Swinger
Bypass Trips, the panel bypasses it until the following conditions occur; the area
in which the zone is assigned is disarmed, the zone is manually reset through the
Bypass Zones keypad User Menu function, the zone remains normal for one hour
and the Reset Swinger Bypass is YES.
If the zone trips fewer than the specied times within one hour of the rst trip,
the bypass trip counter returns to 0 (zero) and the process must be repeated.
A report of the swinger bypass is sent to the receiver if Bypass Reports is YES.
DISARMEDOPEN
MSG:TROUBLE
A T L -
OUTPUTNO: 0
ACTION:
STDPLSMOM FOLW
SWGRBYP NO YES