Emerson E2 - 2.2.2 MultiFlex Boards; 2.2.2.1 MultiFlex 16 Input Board; 2.2.2.2 MultiFlex Combination Input;Output Boards; 3.2.2 Boards Without Enclosures (Snap Track)

viii • Table of Contents 026-1614 Rev 4 5-JAN-2013
6.4.3.1 Add and Connect a BACnet Device ...................................................................................................................... 6-14
7 E2 ETHERNET PEER COMMUNICATIONS...................................................................................................... 7-1
7.1 ETHERNET IP CONFIGURATIONS................................................................................................................................ 7-1
7.2 HARDWARE SPECIFICATIONS..................................................................................................................................... 7-1
7.2.1 Components........................................................................................................................................................ 7-1
7.3 SOFTWARE SPECIFICATIONS ...................................................................................................................................... 7-2
7.4 ETHERNET NETWORK LAYOUTS................................................................................................................................ 7-2
7.4.1 Closed Network Layout...................................................................................................................................... 7-2
7.4.2 Open Network Layout......................................................................................................................................... 7-3
7.5 SOFTWARE SETUP ...................................................................................................................................................... 7-3
7.6 TROUBLESHOOTING ................................................................................................................................................... 7-4
8 ECHELON NETWORK AND HARDWARE SETUP........................................................................................... 8-1
8.1 OVERVIEW ................................................................................................................................................................. 8-1
8.2 WIRING TYPE............................................................................................................................................................. 8-1
8.3 ECHELON NETWORK STRUCTURING (DAISY-CHAINS) .............................................................................................. 8-1
8.3.1 Maximum Number of Echelon Devices.............................................................................................................. 8-2
8.4 DEVICE TERMINATION............................................................................................................................................... 8-2
8.4.1 Using a Termination Block (P/N 535-2715) to Terminate a Daisy Chain......................................................... 8-3
8.5 WIRE RESTRICTIONS.................................................................................................................................................. 8-3
8.6 INSTALLING ECHELON DEVICES ................................................................................................................................ 8-3
8.6.1 Powering Echelon Devices................................................................................................................................. 8-3
8.7 LEDS ......................................................................................................................................................................... 8-4
8.8 OPEN ECHELON DEVICE CONNECTIVITY................................................................................................................... 8-4
8.8.1 Configuring Echelon Devices............................................................................................................................. 8-4
8.8.1.1 Troubleshooting....................................................................................................................................................... 8-5
9 INPUT AND OUTPUT SETUP................................................................................................................................ 9-1
9.1 THE 16AI, 8IO, AND MULTIFLEX INPUTS................................................................................................................. 9-1
9.1.1 Connecting Sensors to Input Boards.................................................................................................................. 9-1
9.1.1.1 Wiring ...................................................................................................................................................................... 9-1
9.1.1.2 Sensor Wiring Types................................................................................................................................................ 9-1
9.1.1.3 Input Type Dip Switches ......................................................................................................................................... 9-1
9.1.2 Power Connection.............................................................................................................................................. 9-2
9.1.3 Input Setup in E2................................................................................................................................................ 9-6
9.1.3.1 Configuring a Point from the Input Definitions/Status Screen................................................................................ 9-6
9.1.3.2 Using the Input Definitions/Status Screen............................................................................................................... 9-7
9.1.3.3 Setting Up Analog Inputs......................................................................................................................................... 9-7
9.1.3.4 Setting Up Digital Inputs ......................................................................................................................................... 9-9
9.2 THE 8RO, 8IO, AND MULTIFLEX OUTPUTS ............................................................................................................ 9-10
9.2.1 Wiring Form C Contacts.................................................................................................................................. 9-10
9.2.2 MultiFlex Relay Outputs .................................................................................................................................. 9-10
9.2.3 Setting the Fail-Safe Dip Switch ...................................................................................................................... 9-11
9.2.4 Relay Output Test Mode................................................................................................................................... 9-11
9.2.5 Wiring Outputs to Points................................................................................................................................. 9-12
9.2.6 The Output LED ............................................................................................................................................... 9-12
9.2.7 Output Setup in E2 ........................................................................................................................................... 9-12
9.2.7.1 Configuring a Point from the Output Definitions/Status Screen........................................................................... 9-12
9.2.7.2 Using the Output Definitions/Status Screen .......................................................................................................... 9-13
9.2.7.3 Setting Up Digital Outputs..................................................................................................................................... 9-13
9.2.7.4 Setting Up Analog Outputs.................................................................................................................................... 9-14
9.3 CC-100 CASE CONTROLLERS .................................................................................................................................. 9-16
9.3.1 Inputs................................................................................................................................................................ 9-16
9.3.2 Power Module Wiring...................................................................................................................................... 9-17