Emerson EL-O-Matic F Series - Appendix B: Tool & Torque Table

Appendix
Appendix: B Tool & Torque Table
This section explains:
• Which tools to use for the indicated fasteners.
• The recommended amount of torque to apply on the indicated fasteners.
Table B-1. End cap bolts
Actuator
size
Thread Tool Size
Torque (Nm) Torque (lbf.ft)
Target Min. Max. Target Min. Max.
12 M4
Allen key
SW 3 1.1 0.8 1.3 0.8 0.6 1.0
25 M5 SW 4 2.0 1.6 3.0 1.5 1.2 2.2
40 M5 SW 4 2.0 1.6 3.0 1.5 1.2 2.2
65 M5 SW 4 2.0 1.6 3.0 1.5 1.2 2.2
100 M5 SW 4 2.0 1.6 3.0 1.5 1.2 2.2
150 M6 SW 5 3.3 2.6 5.1 2.4 1.9 3.8
200 M6 SW 5 3.3 2.6 5.1 2.4 1.9 3.8
350 M8 SW 6 8.4 6.7 12.2 6.2 4.9 9.0
600 M10 SW 8 15.3 12.2 24.8 11.3 9.0 18.3
950 M12 SW10 24.3 19.4 41.6 17.9 14.3 30.7
1600 M12 SW10 24.3 19.4 41.6 17.9 14.3 30.7
2500 M12 SW10 24.3 19.4 41.6 17.9 14.3 30.7
4000 M14 SW12 43.5 34.8 66.4 32.1 25.7 49.0
Table B-2. Bottom flange, Metric units
Actuator
size
ISO Pattern
Metric Torque (Nm) Imperial Torque (lbf.ft)
Thread Min. Max. Thread Min. Max.
12 F04 M6 4.5 5.0 10-24UNC 3.3 3.7
25
F03 inner pattern M5 2.0 3.0 10-24UNC 1.5 2.2
F05 outer pattern M6 4.5 5.0 1/4"-20 3.3 3.7
40, 65, 100
F05 inner pattern M6 4.5 5.0 1/4"-20 3.3 3.7
F07 outer pattern M8 10.5 12.5 5/16"-18 7.7 9.2
150, 200, 350
F07 inner pattern M8 10.5 12.5 5/16"-18 7.7 9.2
F10 outer pattern M10 21.0 24.5 3/8"-16 15.5 18.1
600
F10 inner pattern M10 21.0 24.5 3/8"-16 15.5 18.1
F12 outer pattern M12 34.5 43.0 1/2"-13 25.4 31.7
950
F10 inner pattern M10 21.0 24.5 3/8"-16 15.5 18.1
F14 outer pattern M16 90.0 104.0 5/8"-11 66.4 76.7
1600, 2500
F16 inner pattern M20 170.0 204.0 3/4"-10 125.4 150.5
F25* outer pattern 4x M16 90.0 104.0 4x 5/8"-11 66.4 76.7
4000
F16 inner pattern M20 170.0 204.0 3/4"-10 125.4 150.5
F25 outer pattern 8x M16 90.0 104.0 8x 5/8"-11 66.4 76.7
1. For actuator sizes 1600 and 2500 only 4 holes of the ISO5211 F25 drilling pattern are available.
Installation, Operation and Maintenance Manual
DOC.IOM.EF.EN Rev. 7
September 2017
55
Appendix