Chapter 8—Insert Effect Parameters
To access the Parameters described on this page (unless otherwise noted):
Press Effects, turn the Parameter knob to select Insert Effect, and press Enter. Turn the Parameter
knob to select the parameter, and use the Value knob to change the parameter's Setting.
28 ENSONIQ MR-Rack Musician’s Manual
VCF Release 1ms to 10.0s Sets the amount of time after the incoming signal has ceased for the
envelope follower to shut down. Generally these times are longer than
the attack times.
Post HPF Fc 10Hz to 1.50kHz Filters out the low frequencies after the distortion.
29 ResVCF→DDL
VCF
Right
Left
ADSR
Envelope Generator
Output
L
R
2-Tap DDL
R
e
s
V
C
F
→
DD
L
c
o
m
b
i
n
e
s
a
v
o
l
t
a
g
e
c
o
n
t
r
o
l
f
il
t
e
r
a
n
d
a
d
i
g
i
t
a
l
d
e
l
a
y
.
Parameter Range Description
VCF Input Off, -49.5dB to 0.0dB Acts as a trim control at the input of the VCF.
VCF Fc 10Hz to 7.10kHz Determines the VCF cut off frequency. Higher values have a brighter
sound. This parameter can be modulated, using a CV Pedal for a wah
wah pedal effect.
VCF Q 1.0 to 40.0 Determines the level and width of the resonant peak at the filter cutoff
point. While the Fc (filter cutoff) parameter determines where (at what
frequency) this peak will occur, the Q setting controls the presence of the
peak. This setting is important for the auto-wah effect.
ADSR Attack 50us to 10.0s Sets the attack time for the ADSR Envelope shape.
ADSR Decay 50us to 10.0s Sets the decay time for the ADSR Envelope shape.
ADSR Sustain Off, -49.5dB to 0.0dB Sets the sustain level for the ADSR Envelope shape.
ADSR Release 50us to 10.0s Sets the release time for the ADSR Envelope shape.
ADSR Env Amt -99% to +99% Determines the degree to which the envelope modifies the cutoff
frequency of the VCF.
ADSR TrigMode Single or Multi Determines whether the envelope which controls the VCF will retrigger
with each key-event (Multi) or not (Single).
Dly1 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the amount of delay time for the first independent delay.
Dly1 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the original dry signal.
Dly1 Feedback -99% to +99% Determines the amount of signal that will be fed from the output back
into the input, increasing the number of repeats in the delay.
Dly1 Damping 100Hz to 21.2kHz Controls the cutoff of a low pass filter on the feedback signal, which
adjusts the amount of damping to the feedback signals. The higher the
number, the more the signals are damped.
Dly1 Pan Full <L to Full >R Determines the location of the delay in the stereo spectrum.
Dly2 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the amount of delay time for the second independent delay.
Dly2 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the original dry signal.
Dly2 Feedback -99% to +99% Determines the amount of signal that will be fed from the output back
into the input, increasing the number of repeats in the delay.
Dly2 Damping 100Hz to 21.2kHz Controls the cutoff of a low pass filter on the feedback signal, which
adjusts the amount of damping to the feedback signals. The higher the
number, the more the signals are damped.
Dly2 Pan Full <L to Full >R Determines the location of the delay in the stereo spectrum.
30 Dist→VCF→DDL
To Next Page
Loading...
