Chapter 8—Insert Effect Parameters
To access the Parameters described on this page (unless otherwise noted):
Press Effects, turn the Parameter knob to select Insert Effect, and press Enter. Turn the Parameter
knob to select the parameter, and use the Value knob to change the parameter's Setting.
38 ENSONIQ MR-Rack Musician’s Manual
Amp Mid1Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this mid frequency
parametric.
Amp Mid2 Fc 10Hz to 20.0kHz Identical to the Mid 1 Fc parameter, and is used to control different
bandwidths within the mid range.
Amp Mid2 Q 1.0 to 40.0 Identical to the Mid 1 Q parameter, and is used to control different
bandwidths within the mid range.
Amp Mid2Gain Off, -49.5dB to +24dB Identical to the Mid 1 Gain parameter, and is used to control different
bandwidths within the mid range.
Amp TrebGain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to the high shelving filter.
PostEQ Level Off, -49.5dB to +24dB This parameter controls the output level of the main amp before the
output EQ.
Speaker LPF 10Hz to 20.0kHz Attenuates the high frequency content of the signal driving the distortion
at a rate of 6dB per octave starting at the corner frequency set by this
parameter.
The high-frequency bandwidth acts as a low pass filter on the signal
going into the distortion, controlling the amount of high frequencies that
will pass into the effect. The higher the setting, the more high
frequencies are allowed to pass. This functions like a tone control on a
guitar.
Gate Thresh -96.0dB to 0.0dB Sets the upper threshold level at which the noise gate passes the audio.
Gate Hysteresis 0dB to 48dB Sets the lower threshold level relative to Gate Thresh, below which the
noise gate shuts off the audio.
Dly1 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the amount of delay time for the first independent delay.
Dly1 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the original dry signal.
Dly1 Feedback -99% to +99% Determines the amount of signal that will be fed from the output back
into the input, increasing the number of repeats in the delay.
Dly1 Damping 100Hz to 21.2kHz Controls the cutoff of a low pass filter on the feedback signal, which
adjusts the amount of damping to the feedback signals. The higher the
number, the more the signals are damped.
Dly1 Pan Full <L to Full >R Determines the location of the delay in the stereo spectrum.
Dly2 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the amount of delay time for the second independent delay.
Dly2 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the original dry signal.
Dly2 Pan Full <L to Full >R Determines the location of the delay in the stereo spectrum.
37 Dist→DDL→Trem
Distortion
Right
Left
Lo Shelf Mid 1 Mid 2 Hi Shelf Output
L
R
2-Tap DDL Tremolo
A
g
u
i
t
a
r
-
e
ff
ec
t
c
h
a
i
n
t
h
a
t
i
n
c
l
u
d
e
s
v
o
l
t
a
g
e
-
c
o
n
t
r
o
ll
e
d
d
i
s
t
o
r
t
i
o
n
,
p
a
r
a
m
e
t
r
i
c
E
Q
,
d
i
g
i
t
a
l
d
e
l
a
y
,
a
n
d
L
F
O
m
o
d
u
l
a
t
i
o
n
.
Parameter Range Description
Dist LPF Fc 10Hz to 20.0kHz Filters out high frequencies prior to the distortion.
Dist Offset -99% to +99% Adjusts the balance of even-to-odd-generated harmonics.
Dist Gain Off, -49.5dB to +48dB Controls the gain going into the distortion effect. This will boost the
signal level up to 48 dB. For more distortion, use a high input level gain
and turn the Distortion Volume down to keep the volume under control.
For less distortion, use a low gain input level and a higher output volume.
Dist Curve Soft, Medium 1, Medium
2, Hard, Buzz
Selects the type of clipping produced by the distortion. The curves range
from tube-like distortion (Soft) to nasty distortion (Buzz).
Dist Volume Off, -49.5dB to 0.0dB Controls the volume of the distortion effect. Generally, if the Distortion
Gain is set high, set this parameter lower.
To Next Page
Loading...
