Chapter 8—Insert Effect Parameters
To access the Parameters described on this page (unless otherwise noted):
Press Effects, turn the Parameter knob to select Insert Effect, and press Enter. Turn the Parameter
knob to select the parameter, and use the Value knob to change the parameter's Setting.
ENSONIQ MR-Rack Musician’s Manual 31
31 Pitch Detuner
Right
Voice 1
DDL
Voice 2
Voice2
Regen
Voice1 Level
Voice2 Level
Voice 1
Regen
Left
Out
Left
Voice 1
DDL
Voice 2
Voice2
Regen
Voice1 Level
Voice2 Level
Voice 1
Regen
Right
Out
P
i
t
c
h
D
e
t
u
n
e
r
a
ll
o
w
s
y
o
u
t
o
c
h
a
n
g
e
t
h
e
p
i
t
c
h
o
f
a
s
o
u
n
d
t
o
a
n
y
p
i
t
c
h
w
i
t
h
i
n
a
r
a
n
g
e
o
f
t
w
o
o
c
t
a
v
e
s
i
n
e
i
t
h
e
r
d
i
r
ec
t
i
o
n
.
Parameter Range Description
Voice1 Semi -24 semi to +24 semi Allows you to adjust the pitch of Voice 1 up to two octaves above or
below the original pitch in semi-tones (half steps).
Voice1 Fine -100cent to +100cent This parameter allows you to fine tune the pitch of Voice 1.
Voice1 Level Off, -49.5dB to 0.0dB Adjusts the volume of Voice 1.
Voice1 Regen -99% to +99% Controls the amount of feedback from the output of the pitch detuner
back into the input. This allows you to create special effects with
ascending/descending delays.
Voice1 Width 1ms to 185ms Controls the splice width of voice 1. Select the width that sounds best to
you. Shorter values result in a grainier sound, while longer values sound
smoother.
Voice1 Mod 0% to 100% Controls the amount of modulation applied to Voice 1.
Voice2 Semi -24 semi to +24 semi Allows you to adjust the pitch of Voice 2 up to two octaves above or
below the original pitch in semi-tones (half steps).
Voice2 Fine -100cent to +100cent This parameter allows you to fine tune the pitch of Voice 2.
Voice2 Level Off, -49.5dB to 0.0dB Adjusts the volume of Voice 2.
Voice2 Regen -99% to +99% Controls the amount of feedback from the output of the pitch detuner
back into the input. This allows you to create special effects with
ascending/descending delays.
Voice2 Width 1ms to 185ms Controls the splice width of voice 2. Select the width that sounds best to
you. Shorter values result in a grainier sound, while longer values sound
smoother.
Voice2 Mod 0% to 100% Controls the amount of modulation applied to Voice 2.
LFO Rate 1/1 Sys to 1/32 Sys, 0.0Hz
to 20.0Hz
This parameter controls the rate of pitch modulation which creates a
chorusing effect. To achieve chorusing, this rate must be very low.
LFO Shape Triangle, Sine, Sawtooth,
Square, Asym, Step
Determines the shape that the LFO will use for pitch modulation.
LFO Phase -180deg to +180deg Controls the relative phase between left and right LFOs.
Regen Time 1/1 Sys to 1/32 Sys, 0ms to
185ms
Controls the amount of delay in the feedback path.
To Next Page
Loading...
Need help?
General
