evertz 5600ACO2 - How to Use this Manual

To Next Page

To Previous Page

Model 5600ACO2 Automatic Changeover Unit

1.1. HOW TO USE THIS MANUAL

This manual is organized into 4 chapters: Overview, Installation, Operation, and Technical Information.

There are individual tables of contents at the beginning of each chapter as well as an overall table of

contents at the beginning of the manual to aid in finding the information you want.

This symbol is intended to alert the user to important operating

instructions.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important safety related operating and maintenance

(Servicing) instructions in this manual.

OVERVIEW

Revision 1.3 Page 1-5

Main Page

Table of Contents7
Overview11
Figure 1-1: 5600ACO2 Block Diagram13
Figure 1-2: Redundant Master Clock/Spg with Auto-Changeover System Diagram14
How to Use this Manual15
Installation17
Rear Panel17
Coaxial Connections17
Figure 2-1: 5600ACO2 Rear Panel17
Balanced AES, DARS and Analog Audio Connections18
Linear Time Code, Parallel Remote Control and Auxiliary Connections18
Ethernet Connections19
Power Connections20
Mounting20
Power Requirements20
5600Msc Connections20
Sync Outputs20
10 Mhz Output21
Word Clock Output21
Unbalanced DARS and AES Outputs21
Balanced DARS, AES and Analog Audio Outputs21
Video Test Signal Generator Outputs22
LTC and GPIO Connections22
Synchronizing the Menu Settings of the Two 5600MSC Units23
Connecting the General Purpose Inputs and Outputs23
Figure 2-2: Typical GPI Circuitry24
Figure 2-3: GPO1 Output Circuitry24
Figure 2-4: GPO2 Output Circuitry24
How to Operate the Automatic Changeover25
An Overview of the Status Indicators25
Operating Mode Indicators25
Figure 3-1: Model 5600ACO2 Front Panel Layout25
Input Indicators26
ACO GPI Indicators26
Power Supply Indicators26
Front Panel Control26
Automatic Changeover Mode27
Manual GPI Changeover Mode27
Manual Front Panel Changeover Mode27
Dip Switches27
GPI Input Mode27
Table 3-4: Dual GPI Mode Operation28
GPI Changeover Rate29
Bank a Priority29
DARS Valid Condition29
Table 3-5: Changeover Rate Switch Settings29
Table 3-6: Bank a Priority Switch Settings29
Table 3-7: DARS Valid Condition Switch Settings29
AES Valid Condition30
GPI Monitoring30
Table 3-8: AES Valid Condition Switch Settings30
Table 3-9: GPI Monitoring Switch Settings30
HDSDI/SDI Monitoring31
Change Limiting31
Table 3-10: HDSDI/SDI Monitoring Switch Settings31
Table 3-11: Change Limiting Switch Settings31
Gpo Tally Outputs32
Technical Description33
Specifications33
LTC Outputs33
Coaxial Inputs and Outputs33
Balanced DARS, AES and Analog Audio Inputs and Outputs33
ACO General Purpose Inputs and Outputs33
MSC General Purpose Inputs and Outputs34
Changeover Conditions34
Ethernet34
Electrical34
Physical34
Upgrading the Firmware35
Overview35
Terminal Program Setup35
Initiating Firmware Upgrade Mode from the Terminal Program35
Uploading the New Firmware36
Completing the Upgrade36
Serial Port Configuration and Status36
Network Configuration38
SNMP Configuration38
Voting Control39
Show Status40
Servicing Instructions41
Changing the Fuses41
Vistalink Configuration and Control43
Connecting the 5600ACO2 to Vistalink43
Installing Vistalink43
Using Vistalink to Configure the 5600ACO244
Figure 5-1: Vistalink Configuration - Voting Control45
Using Vistalink to Monitor the 5600ACO246
Using Vistalink46
Figure 5-2: Vistalink Monitoring - General Status46
Figure 5-3: Vistalink Monitoring - GPIO Status47
To Enable the Fault Reporting Traps of the 5600ACO248
Figure 5-4: Vistalink Monitoring - Analog Sync and TG Faults48
Figure 5-5: Vistalink Monitoring - LTC Faults49
Figure 5-6: Vistalink Monitoring GPIO Faults50
Figure 5-7: Vistalink Monitoring - SDI and HDSDI Test Generator Faults51
Figure 5-8: Vistalink Monitoring - AES, DARS and Miscellaneous Faults52

evertz 5600ACO2 - How to Use this Manual

Table of Contents

Related product manuals