Command and Response Table for Matrix Switcher Commands (continued)
DTP CrossPoint 4K Series Matrix Switchers • Programming Guide 65
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Vertical shift
Specify a value
EX2!
*
X3!
VCTR
}
Vctr
X2!
*
X3!]
Set the vertical location of first active line
in output
X2!
.
Increment value
EX2!
+VCTR
}
Vctr
X2!
*
X3!]
Increment the value by one line (shift up).
Decrement value
EX2!
–VCTR
}
Vctr
X2!
*
X3!]
Decrease the value by one line (shift down).
View
EX2!
VCTR
} X3!]
Show the vertical location of first active
line in output
X2!
.
Horizontal size (image)
Specify a value
EX2!
*
X3!
HSIZ
}
Hsiz
X2!
*
X3!]
Set the horizontal of output
X2!
.
Increment value
EX2!
+HSIZ
}
Hsiz
X2!
*
X3!]
Increment the value by one pixel (make
one pixel wider).
Decrement value
EX2!
–HSIZ
}
Hsiz
X2!
*
X3!]
Decrement the value by one pixel (make
one pixel narrower).
View
EX2!
HSIZ
} X3!]
Show the horizontal size of output
X2!
.
Vertical size (image)
Specify a value
EX2!
*
X3!
VSIZ
}
Vsiz
X2!
*
X3!]
Set the vertical of output
X2!
.
Increment value
EX2!
+VSIZ
}
Vsiz
X2!
*
X3!]
Increment the value by one pixel (make
one pixel taller).
Decrement value
EX2!
–VSIZ
}
Vsiz
X2!
*
X3!]
Decrement the value by one pixel (make
one pixel shorter).
View
EX2!
VSIZ
} X3!]
Show the vertical size of output
X2!
.
Combined image position and size
Specify all size and position values
EX2!
,
X3!
*
X3!
*
X3!
*
X3!
XIMG
}
Ximg
X2!
,
X3!
*
X3!
*
X3!
*
X3!]
Command description:
E
output number, horizontal shift*vertical shift*horizontal size*vertical size XIMG
}
Example:
E
6,0*0*3840*2160XIMG
}
Ximg6,+00000*+00000*03840*02160
]
View all size and position values
EX2!
XIMG
} X3!
*
X3!
*
X3!
*
X3!]
View active pixels and lines
View active pixels
EX2!
APIX
}
Apix
X2!
*
X3@]
NOTE: The “Apix
X2!
*” portion of the response appears only when the switcher is in Verbose mode 2 or 3.
View active lines
EX2!
ALIN
}
Alin
X2!
*
X3@]
NOTE: The “Alin
X2!
*” portion of the response appears only when the switcher is in Verbose mode 2 or 3.
Aspect ratio
NOTE: The aspect ratio effect is applied only when the input (
X!
) is tied to a scaled output (5 through 8).
Set to fill
EX!
*1ASPR
}
Aspr
X!
*1
]
Always fill the output.
Set to follow
EX!
*2ASPR
}
Aspr
X!
*2
]
Follow the input aspect ratio.
View aspect ratio
EX!
ASPR
} X3#]
Execute Auto-Image
Execute Auto-Image
X2!
*A Img
X2!]
NOTE: X! = Input number 01 – 10
X2! = TP (scaled) and insertion output number 05 – 08
X3! = Position and size ±10240 (Horizontal is specified from left, vertical from top, 0 is reported as positive [+] )
X3@ = Active pixels and active lines Dependent on the input signal and selected scaling.
X3# = Aspect ratio fill or follow 1= fill (default) 2 = follow
To Next Page
