Fisher FIELDVUE DVC6200 - Section 8 Parts; Parts Ordering; Parts Kits

Instruction Manual
D103409X012
Parts
May 2013
113
Section 8 Parts88
Parts Ordering
Whenever corresponding with your Emerson Process Management sales office about this equipment, always mention
the controller serial number. When ordering replacement parts, refer to the 11‐character part number of each
required part as found in the following parts list. Part numbers are shown for kits and recommended spares only. For
part numbers not shown, contact your Emerson Process Management sales office.
WARNING
Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Process Management should
not, under any circumstances, be used in any Fisher instrument. Use of components not supplied by Emerson Process
Management may void your warranty, might adversely affect the performance of the instrument, and could cause personal
injury and property damage.
Parts Kits
Kit Description Part Number
1* Elastomer Spare Parts Kit (kit contains parts to
service one digital valve controller)
Standard 19B5402X012
Extreme Temperature option
(fluorosilicone elastomers) 19B5402X022
2* Small Hardware Spare Parts Kit (kit contains parts
to service one digital valve controller) 19B5403X012
3* Seal Screen Kit
[kit contains 25 seal screens (key 231)
and 25 O‐rings (key 39)]
Standard and Extreme Temperature option 14B5072X182
(fluorosilicone elastomers)
4* Terminal Box Kit, aluminum
Standard 19B5401X012
Standard, Natural Gas approved 19B5401X032
Extreme Temperature option (fluorosilicone
elastomers) 19B5401X022
Extreme Temperature option (fluorosilicone
elastomers) Natural Gas Approved 19B5401X042
5* I/P Converter Kit
Standard 38B6041X152
For Extreme Temperature option
(fluorosilicone elastomers) 38B6041X132
Kit Description Part Number
6* Spare Module Base Assembly Kit, Aluminum
[kit contains module base (key 2); drive screws, qty. 2,
(key 11); shield/label (key 19); hex socket cap screw, qty. 3,
(key 38); self tapping screw, qty. 2 (key 49); pipe plug, qty. 3
(key 61); retaining ring, qty. 3 (key 154); screen (key 236);
and flame arrestors, qty. 3 (key 243)] GE18654X012
7* Spare Housing Assembly Kit, aluminum
[kit contains housing (key 1); vent assembly (key 52);
seal (only included in Housing A kits) (key 288);
seal (key 237); O‐ring (key 34); O‐ring (only used
with integrally mounted regulator) (key 5)]
Housing A (used for GX actuator)
Standard (nitrile elastomers) GE48798X012
Extreme Temperature option
(fluorosilicone elastomers) GE48798X022
Housing B (used for all actuators except GX)
Standard (nitrile elastomers) GE48798X052
Extreme Temperature option
(fluorosilicone elastomers) GE48798X062

8* Spare I/P Shroud Kit
[kit contains shroud (key 169) and
hex socket cap screw, qty. 4 (key 23)] GE29183X012
9* Remote Mount Feedback Unit Kit (see figure 8‐5)
[remote housing assembly (key25); hex socket set
screw (key 58); 1/2 NPT pipe plug (key 62); wire retainer, qty 2
(key 131); terminal cover (key 255); o-ring (key 256); gasket
(Housing A only, used for GX actuator) (key 287); seal
(Housing A only, used for GX actuator) (key 288)
Housing A (used for GX actuator) GE46670X012
Housing B (used for all actuators except GX) GE40178X012
*Recommended spare parts