Flyer UPROC - Selecting system settings; Starting up the e-bike system

16
Use
Beforeinitialstart-up
The KIOX comes with a partially charged battery.
Beforetherstuse,thebatterymustbecharged
for at least one hour via the USB socket or via the
e-bike system.
Theon-boardcomputershouldbettedsuchthat
the buttons are almost vertical to the handlebars.
When you start up the unit for the rst time,
you will rst be prompted to select a language.
You can then navigate to the menu item <Kiox
Introduction> for a description of the key func
-
tions and displays. This menu item can also be
accessed later on via
<Settings> → <Informa-
tion>.
Selecting
systemsettings
Place the on-board computer in the holder and
follow the steps below with your bike standing up:
Navigate to the status screen (using the < button
(10) on the on-board computer until you reach the
rstdisplay)andselectsettingsusingtheselect
key.
Using the – (11) and + (12) buttons, you can se
-
lect the desired settings and open these and any
other sub-menus using the select key
(9). You can
navigate back to the previous menu from any set-
tings menu using the back button (10).
Y
ou can adjust the following settings under Sys-
tem settings:
<Brightness>
<T
ime>
<Date [DD.Mon.YYYY]>
<Time zone>
<24h form (24h time format)>
<Brgh backg. (Bright background)>
<Imp. units (Imperial units)>
<Language>
<Factory reset>
Startingupthee-bikesystem
Requirements
The e-bike system can only be activated if the fol
-
lowing requirements are met:
• Thee-bikebatteryissu󰀩ciently charged (see
battery user manual)
• The on-board computer is tted in the holder
correctly
Switchingthee-bikesystemon/o󰀨
The e-bike system can be switched on in the fol-
lowing ways:
•
Place the on-board computer in the holder (5).
• Brieypresstheon/o󰀨buttons(4) on the on-
board computer and on the e-bike battery you
havetted.
• Press the e-bike battery on/o󰀨 button on the
on-board computer (some models do not have
an on/o󰀨 button for the battery; see battery
user manual).
The drive is activated once you start pedalling
(apart from with the pushing aid feature or in as
-
sistance level OFF). The motor output is based on
the assistance level set
in the on-board computer.
If you stop pedalling or reach a speed of
25/45km/h during normal use,
thee-bikedriveswitcheso󰀨theassistance.The
drive is reactivated automatically once you start
pedalling and while the speed remains under
25/45km/h.
The e-bike system can be switched o󰀨 in the
following ways:
• Press the on/o󰀨 button (4) on the on-board
computer for at least one second.
• Switch o󰀨 the E-bike battery using its on/o󰀨
button(somemodelsdonothaveanon/o󰀨but
-
ton for the battery; see the bike manufacturer’s
user manual).
•
Remove the on-board computer from the hold-
er.
If no more power is required from the E-bike
drive (e.g. because the E-bike is at a standstill)
for around ten minutes and you do not press any
buttons on the E-bike’s on-board computer or
on-board computer, the E-bike system and the
battery switch o󰀨 automatically in order to save
energy.
Powersupplyoftheon-boardcomputer
If the on-board computer is in the holder (5), a
su󰀩cientlychargede-bikebatteryisinsertedinto
the e-bike and the e-bike system is switched on,
then the on-board computer battery is powered by
the e-bike battery.
If the on-board computer is removed from the
holder (5), the power is supplied by the on-board
computer battery. If the on-board computer bat
-
tery’s charge is running low, a warning message
appears on the display
.
To charge the on-board computer battery, slide
the on-board computer back onto the holder (5).
Note that if you do not charge the e-bike battery
straight away, the e-bike system will automatical
-
ly
switch o󰀨after10minutes ofinactivity.If this
happens, the on-board computer battery will also
stop charging.
You can also charge the on-board computer via
the USB port. To do this, open the protective cov
-
er (17).
Use a Micro-USB cable to connect the
USB port (6) on the on-board computer to a com-
mercially available USB charger (not included
with
the product as standard) or to the USB port
ofacomputer(max.5Vchargingvoltage;max.
500 mA charging current).