FujiFilm EP-6000 - Troubleshooting

To Next Page

To Previous Page

SS1807-N002 Failure Analysis － 2/64

1. Troubleshooting

Refer to the troubleshooting in operation manual.

→ EP-6000 Operation Manual, “10.1 Troubleshooting”

Main Page

Default Chapter3
- About this Manual3
- Notation in the Manual4
General Table of Contents5
- Table of Contents6
Caution in Safety13
Safety Cautions14
- Infection Related Caution14
- General Caution17
Label18
- EP-6000 Labeling Layout (FV693A)18
Product Specifications25
EP-6000 Specifications26
- Basic Specifications26
  - Catalog Specifications26
- Detailed Specifications27
- Functions29
- Auxiliary Functions31
- Quality31
- Regurations32
- Block Diagram33
Disposal34
Change History35
- ECN Publication History35
- Software Version History35
Instruction of System36
Security37
- Category37
- Log in / Logoff38
  - Login38
  - Logoff39
- Password Change40
- Password Change for "User" and "Administrator40
- Password Change for "Service41
System Configuration42
Display43
- Screen Display Setup44
- Error Message Display54
- P in P Setup54
- Data Display Switch55
- Basic Setup56
- Light Source67
  - Light Emitting Time68
  - Lgdet68
- Endoscope69
- Service79
Peripheral Setup94
- Image Memory95
  - Internal Memory96
- Network Setup97
  - Ping（Ftp99
  - NTP Setup100
    - Ping (NTP)100
    - NTP Check100
- Printer101
  - Printer Setup102
- Recorder106
  - Still Recorder107
- Others108
  - Card Information Setup109
Image Setup110
- Image Setting111
  - Screen Display Setup112
    - Zoom Ratio of Electronic Zoom112
    - Color Mode112
- Light Control113
  - Screen Display Setup114
    - Brightness Limit for Auto Metering Mode114
    - Brightness Adjustment for Peak Metering114
- Basic Setting115
  - Items Reset at Power-On116
    - Screen for Setting Items Reset at Power-On116
Language Setup118
- Keyboard Setup120
- Built-In Language120
- Install Language120
System Information121
Setting of the Network122
- Outline122
- Description124
  - Communication System124
  - Connection124
- Network Settings on the EP-6000125
- Settings on the FTP Server126
  - Setting the TCP/IP126
- Confirmation of Network Connection127
  - Confirmation of Cable Connection (Confirmation of LED)127
  - Confirmation of Ping127
Software Version Upgrade128
- Preparation128
- Version Upgrade Procedure128
- Checking Version up130
EP-6000 Description of Configuration131
- Block Diagram131
- Schematic Diagram132
- Connector Pin Layout134
- Outline of PCB Roles139
Failure Analysis142
Troubleshooting143
Error Message144
Checkup, Replacement and Adjustment206
1 Parts Exchange Procedure210
- Top Cover210
- Filter211
- Front Cover212
- Power Switch214
- Key Top Assy216
- Small Cover Unit221
- One Connector Plate Assy223
- Light Source Unit227
- Air Guide Pipe232
- Air Tube234
- Photo Interrupter235
- Harnes LG_PI-WOC236
- Woc Pcb243
- Elc Pcb247
- Pump251
- Fan (Light Source Unit Side)253
- Fan (Power Supply PCB Side)256
- Power Supply PCB258
- Noise Filter260
- Inlet Assy262
- Fuse265
- EVE Connector266
- Io/Lores Pcb268
- Main PCB270
- Patient PCB282
- Usb Pcb284
- Rear Panel289
- Harness IOL-OP291
- Harness ELC-OP293
- Front Frame295
- Foot300
- Keyboard Cover301
- EEPROM Writing Procedure305
  - PC Setup (Performed Only for the First Time)305
  - EEPROM Writing307
- Checking Procedures for Power Supply310
  - Acquiring the Scope Log Data310
  - Checking the Power Supply312
Operation Confirmation after Repair313
- Precautions313
- Preparation for Test313
- Electrical Safety Inspection328
  - Appearance328
  - Function328
- Check Sheet328
- Setting after Operation Confirmation329
Jig/Equipment List330
- JIG List330
- Equipment List336
Service Parts List343
Periodical Maintenance362
Cleaning364
- Filter364
- LG Connector Unit366
- One Connector Unit366
Periodical Checkup367
- Storing Procedures of Config Data367
- Inspection Items368
  - Appearance368
  - Functions368
- Check Sheet375
- Restoring Procedures of Config Data376
Installation377
System Installation378
- Installation Flowchart380
- Installation Onto the Cart (Standard System Installation Example)381
- Connecting the WC-LINK Cable385
- Attaching the Dustproof Filter (Louver)386
- Connecting the Monitor387
- Connecting the Keyboard388
- Installation for System Expansion389
- Printer Connection (Remote System)391
- Printer Connection (RS-232C System)393
- Digital Printer Connection394
- Video Recorder Connection (Remote System)395
- Connecting the Power Source396
- Power Source398
- Connecting the Power Source When Using the Cart399
- Basic Information on Power Cord400
- Attaching the LAN Connector Guard When Using a Network400
Initial Settings at the Time of Installation401
- Flowchart of System Settings at the Time of Installation401
- Basic System Setup Operations402
- Function Tab404
- Display Tab407
- Basic Setting Tab409
- Light Source Tab411
- Endoscope Tab412
- Setting Foot Switch (FS1)423
- Setup for Switching the Shutter Speed During Optical Zoom426
- Setting the Doctor's Name426
- Setting the Procedure Name432
- Setting the Message436
Security Function440
- Access Control with the Security Function441
- Logging in to the Security Function (Changing the Password)442
- Logging off the Security Function444

FujiFilm EP-6000 - Troubleshooting

Table of Contents

Related product manuals