FujiFilm EP-6000 - Printer Connection (Remote System)

To Next Page

To Previous Page

SS1807-N002 Installation － 15/68

1.8 Printer Connection (Remote System)

◆

Note

◆

・ When the image output from the processor is displayed on the monitor via the printer, the image

may flicker or disappear. Connect the monitor used as the main observation screen directly to the

processor.

<Connection 1> When the image is captured by using the switch of Endoscope

Main Page

Default Chapter3
- About this Manual3
- Notation in the Manual4
General Table of Contents5
- Table of Contents6
Caution in Safety13
Safety Cautions14
- Infection Related Caution14
- General Caution17
Label18
- EP-6000 Labeling Layout (FV693A)18
Product Specifications25
EP-6000 Specifications26
- Basic Specifications26
  - Catalog Specifications26
- Detailed Specifications27
- Functions29
- Auxiliary Functions31
- Quality31
- Regurations32
- Block Diagram33
Disposal34
Change History35
- ECN Publication History35
- Software Version History35
Instruction of System36
Security37
- Category37
- Log in / Logoff38
  - Login38
  - Logoff39
- Password Change40
- Password Change for "User" and "Administrator40
- Password Change for "Service41
System Configuration42
Display43
- Screen Display Setup44
- Error Message Display54
- P in P Setup54
- Data Display Switch55
- Basic Setup56
- Light Source67
  - Light Emitting Time68
  - Lgdet68
- Endoscope69
- Service79
Peripheral Setup94
- Image Memory95
  - Internal Memory96
- Network Setup97
  - Ping（Ftp99
  - NTP Setup100
    - Ping (NTP)100
    - NTP Check100
- Printer101
  - Printer Setup102
- Recorder106
  - Still Recorder107
- Others108
  - Card Information Setup109
Image Setup110
- Image Setting111
  - Screen Display Setup112
    - Zoom Ratio of Electronic Zoom112
    - Color Mode112
- Light Control113
  - Screen Display Setup114
    - Brightness Limit for Auto Metering Mode114
    - Brightness Adjustment for Peak Metering114
- Basic Setting115
  - Items Reset at Power-On116
    - Screen for Setting Items Reset at Power-On116
Language Setup118
- Keyboard Setup120
- Built-In Language120
- Install Language120
System Information121
Setting of the Network122
- Outline122
- Description124
  - Communication System124
  - Connection124
- Network Settings on the EP-6000125
- Settings on the FTP Server126
  - Setting the TCP/IP126
- Confirmation of Network Connection127
  - Confirmation of Cable Connection (Confirmation of LED)127
  - Confirmation of Ping127
Software Version Upgrade128
- Preparation128
- Version Upgrade Procedure128
- Checking Version up130
EP-6000 Description of Configuration131
- Block Diagram131
- Schematic Diagram132
- Connector Pin Layout134
- Outline of PCB Roles139
Failure Analysis142
Troubleshooting143
Error Message144
Checkup, Replacement and Adjustment206
1 Parts Exchange Procedure210
- Top Cover210
- Filter211
- Front Cover212
- Power Switch214
- Key Top Assy216
- Small Cover Unit221
- One Connector Plate Assy223
- Light Source Unit227
- Air Guide Pipe232
- Air Tube234
- Photo Interrupter235
- Harnes LG_PI-WOC236
- Woc Pcb243
- Elc Pcb247
- Pump251
- Fan (Light Source Unit Side)253
- Fan (Power Supply PCB Side)256
- Power Supply PCB258
- Noise Filter260
- Inlet Assy262
- Fuse265
- EVE Connector266
- Io/Lores Pcb268
- Main PCB270
- Patient PCB282
- Usb Pcb284
- Rear Panel289
- Harness IOL-OP291
- Harness ELC-OP293
- Front Frame295
- Foot300
- Keyboard Cover301
- EEPROM Writing Procedure305
  - PC Setup (Performed Only for the First Time)305
  - EEPROM Writing307
- Checking Procedures for Power Supply310
  - Acquiring the Scope Log Data310
  - Checking the Power Supply312
Operation Confirmation after Repair313
- Precautions313
- Preparation for Test313
- Electrical Safety Inspection328
  - Appearance328
  - Function328
- Check Sheet328
- Setting after Operation Confirmation329
Jig/Equipment List330
- JIG List330
- Equipment List336
Service Parts List343
Periodical Maintenance362
Cleaning364
- Filter364
- LG Connector Unit366
- One Connector Unit366
Periodical Checkup367
- Storing Procedures of Config Data367
- Inspection Items368
  - Appearance368
  - Functions368
- Check Sheet375
- Restoring Procedures of Config Data376
Installation377
System Installation378
- Installation Flowchart380
- Installation Onto the Cart (Standard System Installation Example)381
- Connecting the WC-LINK Cable385
- Attaching the Dustproof Filter (Louver)386
- Connecting the Monitor387
- Connecting the Keyboard388
- Installation for System Expansion389
- Printer Connection (Remote System)391
- Printer Connection (RS-232C System)393
- Digital Printer Connection394
- Video Recorder Connection (Remote System)395
- Connecting the Power Source396
- Power Source398
- Connecting the Power Source When Using the Cart399
- Basic Information on Power Cord400
- Attaching the LAN Connector Guard When Using a Network400
Initial Settings at the Time of Installation401
- Flowchart of System Settings at the Time of Installation401
- Basic System Setup Operations402
- Function Tab404
- Display Tab407
- Basic Setting Tab409
- Light Source Tab411
- Endoscope Tab412
- Setting Foot Switch (FS1)423
- Setup for Switching the Shutter Speed During Optical Zoom426
- Setting the Doctor's Name426
- Setting the Procedure Name432
- Setting the Message436
Security Function440
- Access Control with the Security Function441
- Logging in to the Security Function (Changing the Password)442
- Logging off the Security Function444

Related product manuals

FujiFilm EP-6000 - Printer Connection (Remote System)

Table of Contents

Related product manuals