Fujitsu ErgoPro m664 Series - Section 1: Disassembling the System Units

98 pages

To Next Page

To Previous Page

PC Specialist's Handbook ErgoPro m664-series

Edition 1 - Release 1 - March 1998 Page 1-1

Section 1 :

Disassembling the system units

Main Page

Lithium Battery3
Table of Contents4
Common Procedures10
- Grounding Yourself10
Grounding the Unit10
- Checking the Input Voltage Setting11
M664-Series Unit Features (Front)12
Unit Features (Front)12
M664-Series Unit Features (Rear)13
Unit Features (Rear)13
Open and Closing the System Cover14
Opening & Closing the System Unit Cover14
Removing the System Board15
Removing and Installing the System Board15
Removing the Hard Disk Drive16
Removing the Power Supply Unit16
Removing and Installing the Hard Disk Drive16
- Removing the CD-ROM Drive17
- Removing the Floppy Disk Drive17
Removing and Installing the Floppy Disk Drive17
Removing and Installing the CD-ROM Drive17
- Removing an Expansion Slot Cover18
- Removing Additional Adapter Card18
Removing/Adding an Expansion Slot Cover18
Removing and Installing the Additional Adapter Card18
Removing a Pentium II Processor19
Inserting and Removing a DIMM Module20
Adding or Removing a DIMM Module20
Replacing the Battery21
System Board Layout24
System Board Rear Connectors25
Jumper Settings26
Configuration Modes26
Typical Front Panel Connectors27
System Board Front Panel Connectors27
Front Panel I/O Connectors28
- Section 3 : System Setup29
Entering Resident Setup Utility (RSU)30
Moving Around in RSU30
Setup Menu Screens30
Maintenance Menu31
Main Menu31
Advanced Menu34
Security Menu39
Power Menu40
Boot Menu41
Exit Menu43
Bios46
- Larger than 8.4 GB HDD BIOS Support46
- Shadow Option Proms46
Drivers46
Utilities46
- Rflash.exe46
- Rsetup.exe46
- Bios Identification46
BIOS Upgrade47
- Ergopro BIOS Upgrade Diskette47
- Dosflash.exe47
Tips & Hints48
- Using ISA Configuration Utility (ICU)48
- Hard Disk Partitioning48
- USB Legacy Support49
- ATA/ATAPI Device Support49
BIOS Power on Self Test (POST)52
- Beep Codes53
- BIOS Error Messages54
BIOS Check Points (POST Codes)55
System Board62
- Form Factor62
- Processor62
- Voltage Regulator62
- Core Logic62
- Super I/O62
- Floppy Disk Controller62
- Keyboard (Mouse) Controller62
- Parallel Port Communication62
- Serial Port Communication63
- System BIOS63
- Video BIOS63
- System Memory63
- Video Memory63
- PCI Bus63
- AGP Interface63
- PCI Bus Enhanced IDE Interface63
- USB Controller64
Video64
- ATI Xpert@Work AGP Add-On Board (AF31554)64
- ATI 3D Charger PCI Add-On Board (AF31552)65
- AMC (ATI Multimedia Channel)66
- Refresh Rates, ATI Xpert@Work AGP66
- Refresh Rates, ATI 3D Charger PCI66
- Video Memory Upgrades67
- Ethernet Subsystem67
Audio67
Add-On Board Slots on System Board68
Front Panel Indicators68
Section 7 : Pin Assignments69
Parallel Port (Standard Mode)70
Serial Ports70
Mouse Port71
Keyboard Connector71
Universal Serial Bus (USB) Connector71
VGA Pass-Through/Amc Connector on ATI Graphics Adapters72
ISA Bus Connector73
PCI Bus Connector74
AGP Connector75
Audio Connectors76
- Microphone Type Connector (if Not as Speaker Type Connector)76
- MIDI/Joystick Connector in Creative Vibra 16XV Adapter76
- Front Panel I/O Connectors77
- Section 8 : Machines Identification79
M664-Series : Structure Code80
Identification Codes81
Machine Specifications84
- Processor Related Information of M664-Series84
- General Information of M664-Series85
- Architecture & Configuration of M664-Series86
System Memory Map87
Memory Configurations M664-Series88
DIMM Recommendations89
DMA Channels90
Interrupt Levels91
I/O Addresses92
PCI Configuration Space Map94
Timer94
Real-Time Clock (RTC) and CMOS RAM94
Power Supply95
- Characteristics95
- Power Consumption (Without Monitor)95
Spare Parts97

Fujitsu ErgoPro m664 Series - Section 1: Disassembling the System Units

Table of Contents

Related product manuals