Fujitsu Primergy RX300 S3 Options Guide

RX300 S3 Options Guide 11
Introduction Options and upgrade
LocalView module (alphanumeric system display)
The LocalView module provides you with the option of displaying system infor-
mation and hardware system faults alphanumerically. This is an intelligent
module with a micro-controller and its own memory, which functions indepen-
dently of the server system.
The LocalView module consists of an LCD display panel and a toggle switch,
both accommodated in a suitable mount. The mechanical mechanism used
allows the LCD display panel to be pulled out and flapped out. Further infor-
mation on operating the display modes are provided in the documentation on
the LocalView module.
Hard disk drives
The server has two drive cage that can accommodate up to six (2x3) SAS/SATA
hard disk drive modules or up to twelve (2x6) SAS hard disk drive modules.
Each hard disk drive module (HDD module) can accommodate a SAS/SATA or
SAS hard disk drive with a maximum height of 1 inch. The module is connected
to the SAS/SATA backplane without cables. This allows hard disk drive modules
to be simply plugged in or pulled out. (for further details see operating manual).
The hard disk drive system is designed for SAS/SATA with a seperate channel
for each of the hard disk drives.
If the server has a corresponding RAID configuration, defective HDD modules
can also be exchanged online (hot-swap).
Additional controllers in non-hot-plug PCI slots
The system board offers five PCI slots. Slots 1-3 are non-hot-plug PCI slots with
a PCI bus speed of 100 MHz. If slot 1 and slot 2 are not occupied, slot 3 can
work with the PCI bus speed of 133 MHz (IDoubleOP™).
PCI slots 4 and 5 are hot-plug PCI slots which can be equipped with controllers
that have hot-plug capability (the hot-plug PCI slots are described in the
Operating Manual).
Optional riser card
Optionally you can install a Riser card into slot 5, which can be equipped with 3
controllers. The bus speed is 100 MHz. Two slots (6 and 7) can be equipped with
short standard PCI controllers and slot 8 can be equipped with a full length full
height PCI controller.

Fujitsu Primergy RX300 S3 Specifications

General

Tcase	78 °C
Bus type	FSB
FSB Parity	Yes
Processor cache	4 MB
Processor cores	2
Processor model	5080
Processor series	Intel Xeon 5000 Series
Processor socket	LGA 771 (Socket J)
Processor threads	4
Processor codename	Dempsey
Motherboard chipset	Intel® 5000P
Processing Die size	162 mm²
Processor frequency	3.73 GHz
Processor cache type	L2
Processor lithography	65 nm
Processor system type	DP
Processor manufacturer	Intel
Processor package size	37.5 x 37.5 mm
Processor front side bus	1066 MHz
Processor operating modes	64-bit
ECC supported by processor	No
Thermal Design Power (TDP)	130 W
Processor core voltage (AC)	1.25 - 1.40 V
CPU multiplier (bus/core ratio)	14
Number of Processing Die Transistors	376 M
Maximum graphics card memory	8 MB
Memory slots	8
Internal memory	2 GB
Internal memory type	DDR2-SDRAM
Maximum internal memory	32 GB
Memory layout (slots x size)	2 x 1 GB
Networking features	Ethernet/Fast Ethernet/Gigabit Ethernet
Expansion slots	1 x PCIe x8, 2 x PCIe x4, 2 x PCI-X
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level	56 dB
Chassis type	Rack (2U)
Compatible operating systems	Windows Server 2003, Novell SUSE Linux Enterprise Server, Red Hat Enterprise Linux, VMware ESX
I/O ports	8 x SAS
Power supply	600 W
Power requirements	100 - 240V, 50/60 Hz
Operating temperature (T-T)	10 - 35 °C
Safety	IEC 60950-1, EN 60950-1
Electromagnetic compatibility	EN 55 022 A, EN 55024, EN 61000-3-2 / -3-3
RAID levels	1, 5, 10, 50
Processor ARK ID	27213

Weight and Dimensions

Depth	785 mm
Width	483 mm
Height	86 mm
Weight	25000 g