EasyManuals Logo

Fujitsu Primergy RX300 S3 Options Guide

Fujitsu Primergy RX300 S3
124 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #10 background imageLoading...
Page #10 background image
10 Options Guide RX300 S3
Options and upgrade Introduction
1.2 Options and upgrade
Second processor
The system board can be upgraded with a second processor. Only processors
of the same type may be used on the system board. The second processor must
have the same clock frequency and the same cache as the first processor.
Upgrading of the main memory
The eight slots for the main memory are suitable for FBD533/PC2-4200F or
FBD667/PC2-5300 Fully Buffered DIMM memory modules. The organization in
two memory banks, 1 and 2 with 4 memory modules each, permits rapid
memory access with four-way interleaving.
Memory modules must always be incorporated in pairs.
ROMB (RAID on motherboard)
The System is extended with an on board Intel I/O processor. If the controller is
activated, it supports RAID Level 0, 1, 10, 5 and 50. "MegaRaid PCI Express™
ROMB" can be activated with two different upgrading kits.
Additional accessible drives
One 5.25-inch bay and one 3,5-inch bay are available for accessible drives.
The 5.25-inch bay can be installed with a 3.5 inch x 0.5 inch floppy disk drive or
a LocalView module and the other bay can be installed with a 5.25-inch x 0,5
inch DVD-ROM drive.
Only for a 3.5“ HDD variant a tape drive can be installed optionally in the left
drive cage (see also the configurator under “Related publications” on
page 117). Two mounting locations are occupied as a result in the drive cage
which are then no longer available for HDD modules.

Other manuals for Fujitsu Primergy RX300 S3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu Primergy RX300 S3 and is the answer not in the manual?

Fujitsu Primergy RX300 S3 Specifications

General IconGeneral
Tcase78 °C
Bus typeFSB
FSB ParityYes
Processor cache4 MB
Processor cores2
Processor model5080
Processor seriesIntel Xeon 5000 Series
Processor socketLGA 771 (Socket J)
Processor threads4
Processor codenameDempsey
Motherboard chipsetIntel® 5000P
Processing Die size162 mm²
Processor frequency3.73 GHz
Processor cache typeL2
Processor lithography65 nm
Processor system typeDP
Processor manufacturerIntel
Processor package size37.5 x 37.5 mm
Processor front side bus1066 MHz
Processor operating modes64-bit
ECC supported by processorNo
Thermal Design Power (TDP)130 W
Processor core voltage (AC)1.25 - 1.40 V
CPU multiplier (bus/core ratio)14
Number of Processing Die Transistors376 M
Maximum graphics card memory8 MB
Memory slots8
Internal memory2 GB
Internal memory typeDDR2-SDRAM
Maximum internal memory32 GB
Memory layout (slots x size)2 x 1 GB
Networking featuresEthernet/Fast Ethernet/Gigabit Ethernet
Expansion slots1 x PCIe x8, 2 x PCIe x4, 2 x PCI-X
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level56 dB
Chassis typeRack (2U)
Compatible operating systemsWindows Server 2003, Novell SUSE Linux Enterprise Server, Red Hat Enterprise Linux, VMware ESX
I/O ports8 x SAS
Power supply600 W
Power requirements100 - 240V, 50/60 Hz
Operating temperature (T-T)10 - 35 °C
SafetyIEC 60950-1, EN 60950-1
Electromagnetic compatibilityEN 55 022 A, EN 55024, EN 61000-3-2 / -3-3
RAID levels1, 5, 10, 50
Processor ARK ID27213
Weight and Dimensions IconWeight and Dimensions
Depth785 mm
Width483 mm
Height86 mm
Weight25000 g

Related product manuals