FUTABA 12FG - Throttle MIX

115
<Functions of Model Menu (Helicopter Functions)>
S1 button
EDIT button
EDIT dial
ŏ3XVKWKHS1EXWWRQ IRU
VHFRQGWR UHWXUQWR WKH
KRPHVFUHHQ
ŏ7XUQWKHEDITGLDOWR
PRYHRQWKHVFUHHQ
ŏ6HOHFWWKHIXQFWLRQ
QDPHDQG UHWXUQWR WKH
SUHFHGLQJVFUHHQ E\
SXVKLQJWKHEDITEXWWRQ
THROTTLE MIX
This function corrects slowing of engine speed
caused by swash plate operation during aileron
or elevator operation. The method of applying
clockwise or counterclockwise torque when
pirouetting can also be corrected.
An acceleration function which temporarily
increases the throttle side correction rate relative to
rapid stick operation can also be set.
When correction is necessary, move the cursor
Setting example
ŏ$,/WR7+5DSSOLHVDORDGWRWKHHQJLQHDQG
FRUUHFWVVORZLQJRIWKHHQJLQHVSHHGZKHQ
WKHDLOHURQVWLFNZDVRSHUDWHG(QJLQH
UDFLQJFDQEHDGMXVWHGLQGHSHQGHQWO\DW
WKHULJKWDLOHURQDQGOHIWDLOHURQE\5DWHV$
DQG%
Setting method
ŏ:KHQXVLQJWKLVIXQFWLRQPRYHWKHFXUVRUWRWKH>$&7@
LWHPDQGSXVKWKH(',7EXWWRQWRVZLWFKWRWKHGDWD
LQSXWPRGH7XUQWKH(',7GLDOWRWKHOHIWDQGSXVKWKH
(',7EXWWRQ21LVGLVSOD\HG
ŏ:KHQ\RXZDQWWRVHWWKHVDPHFRQWHQWVDWRWKHU
FRQGLWLRQVVHOHFWWKHJURXSPRGH
 :KHQ\RXZDQWWRVHWWKHVHOHFWHGFRQGLWLRQRQO\
VHOHFWWKHVLQJOHPRGHLQLWLDOVHWWLQJ
ŏ7KHFRUUHFWLRQUDWHFDQEHVHWE\FXUYH
ŏ$VZLWFKFDQEHVHW
 :KHQ>>@@LVVHWWKHVZDVKPL[LQJIXQFWLRQLV
RSHUDWHGE\PHUHO\VHOHFWLQJWKHFRQGLWLRQ
 :KHQVHWWLQJDQ>21@>2))@VZLWFKPRYHWKHFXUVRU
WRWKH>@LWHPDQGSXVKWKH(',7EXWWRQWRFDOO
WKHVHOHFWLRQVFUHHQDQGVHWWKHVZLWFKDQGLWV21
SRVLWLRQ
to the mixing item corresponding to the mixing
that needs correction and push the EDIT button to
call the curve setup screen, and then correct the
slowing.
<Acceleration function setting>
ŏ$FFHOHUDWLRQFDQEHVHWIRUERWK
VHWWLQJV/HIWDQG5LJKW
ŏ$FFHOHUDWLRQUDWHVHWWLQJ5DWH
ŏ7KHUHWXUQWLPH'XPSLQJDIWHU
RSHUDWLRQFDQEHVHW
ŏ7KHRSHUDWLRQSRLQWZKHQWKH
FRUUHFWLRQUDWHLVLQFUHDVHG
DQGGHFUHDVHGFDQEHVHW
LQGHSHQGHQWO\:KHQDQRSHUDWLRQ
SRLQWLVH[FHHGHGDFFHOHUDWLRQ
RSHUDWLRQLVSHUIRUPHG
(Currently selected condition name)
ŏ6HOHFW>7+5277/(0,;@DWWKHPRGHO
PHQXDQGFDOOWKHVHWXSVFUHHQVKRZQ
EHORZE\SXVKLQJWKH(',7EXWWRQ
ŏ3XVKWKH S1EXWWRQ WR
FDOOQH[WSDJH
ŏ*URXSVLQJOHPRGH
VZLWFKLQJ
(For more information, refer to
the description at the back of this
manual.)
ŏ0L[LQJFXUYHVHWWLQJ
*For a description of the
curve setting method,
see the description at the
back of this manual.
ŏ$FFHOHUDWLRQVHWWLQJV