FUTABA 12FG User Manual

61
<Functions of Linkage Menu>
S1 button
EDIT button
EDIT dial
ŏ3XVKWKHS1EXWWRQ IRU
VHFRQGWR UHWXUQWR WKH
KRPHVFUHHQ
ŏ7XUQWKHEDITGLDOWR
PRYHRQWKHVFUHHQ
ŏ6HOHFWWKHIXQFWLRQ
QDPHDQG UHWXUQWR WKH
SUHFHGLQJVFUHHQ E\
SXVKLQJWKHEDITEXWWRQ
END POINT
6HWVWKHWUDYHOOLPLWSRLQWDQGVSHHGRIHDFKVHUYR
The End Point function adjusts the left and right
servo throws, generates differential throws, and
will correct improper linkage settings.
The Travel rate can be varied from 30% to 140%
in each direction on channels 1 to 12. Also, the
Limit point where servo throw stops may be varied
from 0% to 155%.
Servo travel adjustment
8VHWKH(',7GLDOWRPRYHWKHFXUVRUWRWKH
75$9LWHPRIWKHFKDQQHO\RXZDQWWR
DGMXVWDQGSXVKWKH(',7EXWWRQWRVZLWFKWR
WKHGDWDLQSXWPRGH
7XUQWKH(',7GLDOWRDGMXVWWKHUDWH
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
(When the EDIT button is pushed for 1 second, the rate is
reset to the initial value.)
 3XVKWKH(',7EXWWRQWRHQGDGMXVWPHQWDQG
UHWXUQWRWKHFXUVROPRYHPRGH
5HSHDWWKLVSURFHGXUHIRUHDFKUDWH
Limit point adjustment
8VHWKH(',7GLDOWRPRYHWKHFXUVRUWRWKH
/,0,7LWHPRIWKHFKDQQHO\RXZDQWWRDGMXVW
DQGSXVKWKH(',7EXWWRQWRVZLWFKWRWKH
GDWDLQSXWPRGH
7XUQWKH(',7GLDOWRDGMXVWWKHOLPLWSRLQW
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
(When the EDIT button is pushed for 1 second, the limit point
is reset to the initial value.)
 3XVKWKH(',7EXWWRQWRHQGDGMXVWPHQWDQG
UHWXUQWRWKHFXUVROPRYHPRGH
5HSHDWWKLVSURFHGXUHIRUHDFKOLPLWSRLQW
NOTE: The Servo Speed setting is used to set the servo delay
for each channel, from channel l to channel 12. The system
uses the programmed speed (delay) to slow down servo
position changes. The Servo Speed setting can be varied
from 0 to 27 in each channel.
Servo speed setting
8VHWKH(',7GLDOWRPRYHWKHFXUVRUWRWKH
63(('LWHPRIWKHFKDQQHO\RXZDQWWR
DGMXVWDQGSXVKWKH(',7EXWWRQWRVZLWFKWR
WKHGDWDLQSXWPRGH
7XUQWKH(',7GLDOWRDGMXVWWKHVHUYRVSHHG
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHaVWHSV
(When the EDIT button is pushed for 1 second, the servo
speed is reset to the initial value.)
 3XVKWKH(',7EXWWRQWRHQGDGMXVWPHQWDQG
UHWXUQWRWKHFXUVROPRYHPRGH
5HSHDWWKLVSURFHGXUHIRUHDFKFKDQQHO
ŏ6HOHFW>(1'32,17@DWWKHOLQNDJHPHQXDQGFDOO
WKHVHWXSVFUHHQVKRZQEHORZE\SXVKLQJWKH(',7
EXWWRQ
(The display screen is an example. The screen
depends on the model type.)
ŏ3XVKWKH S1EXWWRQ WR
FDOOQH[WSDJH

FUTABA 12FG Specifications

General

Brand	FUTABA
Model	12FG
Category	Remote Control
Language	English