60
<Functions of Linkage Menu>
S1 button
EDIT button
EDIT dial
ŏ3XVKWKHS1EXWWRQ IRU
VHFRQGWR UHWXUQWR WKH
KRPHVFUHHQ
ŏ7XUQWKHEDITGLDOWR
PRYHRQWKHVFUHHQ
ŏ6HOHFWWKHIXQFWLRQ
QDPHDQG UHWXUQWR WKH
SUHFHGLQJVFUHHQ E\
SXVKLQJWKHEDITEXWWRQ
FAIL SAFE
6HWVWKHVHUYRVRSHUDWLQJSRVLWLRQZKHQWUDQVPLWWHUVLJQDOVFDQQR
ORQJHUEHUHFHLYHGRUZKHQWKHUHFHLYHUEDWWHU\YROWDJHGURSV
(The display screen is an example. The screen
depends on the model type.)
The Failsafe function may be used to set up positions
that the servos move to in the case of radio interference.
This function only works with G3 or PCM receivers
(FM receivers do not have failsafe capability).
You may set either of two positions for each
channel: Hold, where the servo maintains its last
commanded position, or Failsafe, where each servo
moves to a predetermined position. You may choose
either mode for each channel.
The T12FG system also provides you with an
advanced battery monitoring function that warns
you when the receiver battery has only a little
power remaining. In this case, each servo is moved
to the defined failsafe position (PCM1024: CH3
only.) The battery failsafe may be released by
operating a predefined control on the transmitter
(default is throttle), do not continue to fly, land
as soon as possible. Remember, if the predefined
Fail safe setting procedure
8VHWKH(',7GLDODQGPRYHWKHFXUVRUWRWKH
)6LWHPRIWKHFKDQQHO\RXZDQWWRVHWDQG
SXVKWKH(',7EXWWRQWRVZLWFKWRWKHGDWD
LQSXWPRGH
'LVSOD\>)6@E\WXUQLQJWKH(',7GLDOWRWKH
OHIW
*The display blinks.
3XVKWKH(',7EXWWRQ2SHUDWH(',7GLDORU6
EXWWRQWRVWRSVHWWLQJ
*The channel switches to the F/S mode.
0RYHWKHFXUVRUWRWKH)6326LWHPE\
WXUQLQJWKH(',7GLDOWRWKHULJKW
+ROGWKHFRUUHVSRQGLQJVWLFNNQREVOLGHU
HWFLQWKHSRVLWLRQ\RXZDQWWKHVHUYR
WRPRYHWRZKHQWKHIDLOVDIHIXQFWLRQLV
DFWLYDWHGDQGSXVKWKH(',7EXWWRQIRU
VHFRQG
*The set position is displayed in percentage.
*When you want to return that channel to the hold mode, use
the EDIT dial to move the cursor to the "F/S" item and push
the EDIT button to switch to the data input mode. Display
[HOLD] by turning the EDIT dial to the right and then
change the mode by pushing the EDIT button.
control suddenly moves to a position you did not
command, land at once and check your receiver
battery.
'H¿QHVVHUYRSRVLWLRQZKHQVLJQDOVDUHORVWDQG
when receiver battery voltage becomes low.
WARNING
For safety, always set the fail safe functions.
Ɣ(VSHFLDOO\VHWWKHWKURWWOHFKDQQHOIDLOVDIHIXQFWLRQVRWKDW
the servo moves to the maximum slow side for airplanes and
to the slow side from the hovering position for helicopters.
Crashing of the model at full high when normal radio waves
cannot be received due to interference, etc., is very dangerous.
Ɣ,IIDLOVDIHLVUHVHWE\WKURWWOHVWLFNLWPD\EHPLVWDNHQIRUDQ
engine malfunction and will be reset at throttle slow and the model
ZLOOFRQWLQXHWRÀ\,I\RXKDYHDQ\GRXEWVLPPHGLDWHO\ODQG
Battery fail safe setting procedure
%DWWHU\IDLOVDIHFDQEHVHWIRUHDFKFKDQQHO
E\WKHVDPHPHWKRGDVWKHIDLOVDIHVHWWLQJ
SURFHGXUH6HOHFWDQGVHWWKH%$7)6LWHP
>%)6@%DWWHU\IDLOVDIHIXQFWLRQ21
>2))@%DWWHU\IDLOVDIHIXQFWLRQ2))
Battery fail safe release switch setting
7KLVIXQFWLRQWHPSRUDULO\UHOHDVHVWKHEDWWHU\
IDLOVDIHIXQFWLRQIRUWKHIXVHODJHWRUHFRYHU
DIWHUWKHEDWWHU\IDLOVDIHIXQFWLRQZDV
DFWLYDWHGE\DGURSLQWKHUHFHLYHUEDWWHU\
YROWDJH7KLVVHWWLQJVHOHFWVWKHVZLWFKZKLFK
UHOHDVHVWKHEDWWHU\IDLOVDIHIXQFWLRQ
8VHWKH(',7GLDOWRPRYHWKHFXUVRUWRWKH
>5(/($6(%$77(5<)6@LWHP
3XVKWKH(',7EXWWRQ
*The switch selection screen is called.
*For a detailed description of the switch selection and ON/
OFF direction setting method, see [Switch Setting Method]
at the back of this manual.
ŏ6HOHFW>)$,/6$)(@DWWKHOLQNDJHPHQXDQGFDOO
WKHVHWXSVFUHHQVKRZQEHORZE\SXVKLQJWKH(',7
EXWWRQ
ŏ3XVKWKH S1EXWWRQ WR
FDOOQH[WSDJH
To Next Page
Loading...
Need help?
General
