2
Compliance Information Statement (for U.S.A.)
This device complies with part 15 of the FCC Rules. Operation is subject to the following three conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may
cause undesired operation.
(3)RF Radiation Exposure Statement (For T10PX)
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
RF Radiation Exposure Statement (For R404SBS / R404SBS-E)
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radio and your body.
The responsible party for the compliance of this device is:
Futaba Service Center
2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.
TEL 1-256-461-9399 or E-mail: contactus@futaba.com
CAUTION:
To assure continued FCC compliance:
Any changes or modications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
Compliance Information Statement (for Canada)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation
of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter.
French: Cet appareil radio est conforme au CNR-247 d’Industrie Canada. L’utilisation de ce dispositifest autorisée seulement aux deux condi-
tions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélec-
trique reçu, même sice brouillage est susceptible de compromettre le fonctionnement du dispositif. Cet équipement est conforme aux limites
d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet émetteur ne doit
pas être co-situé ou fonctionner conjointement avec une autre antenne ou émetteur.
Declaration of Conformity (for EU)
Hereby, Futaba Corporation declares that the radio equipment type is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.rc.futaba.co.jp/english/dl/declarations.html
INTRODUCTION
Thank you for purchasing a Futaba F-4G 2.4GHz 10PX digital proportional R/C system. This system is extremely versatile and may be used
by beginners and pros alike. In order for you to make the best use of your system and to drive safely, please read this manual carefully. If you
have any diculties while using your system, please consult the manual, our online Frequently Asked Questions (on the web pages referenced
below), your hobby dealer.
Due to unforeseen changes in production procedures, the information contained in this manual is subject to change without notice.
Please note that the illustrations and screen images in this manual may dier from the actual product.
http://www.futabausa.com
(https://www.rc.futaba.co.jp/)
Application, Export, and Modication
1. This product is only designed for use with radio control models. Use of the product described in this instruction manual is limited to radio
control models.
2. Exportation precautions:
(a) When this product is exported, it cannot be used where prohibited by the laws governing radio waves of the destination country.
(b) Use of this product with other than models may be restricted by Export and Trade Control Regulations.
3. Modication, adjustment, and replacement of parts: Futaba is not responsible for unauthorized modication, adjustment, or replacement of
parts on this product.
OUTSIDE NORTH AMERICA
Please contact the Futaba importer in your region of the world to assist you with any questions, problems or service needs. Please recognize
that all information in this manual, and all support availability, is based upon the systems sold in North America only. Products purchased
elsewhere may vary. Always contact your region’s support center for assistance.
To Next Page
Loading...
Need help?
General
