To Next Page

To Previous Page

1-4 F650 Digital Bay Controller GEK-106310AB

1.1 IMPORTANT PROCEDURES 1 GETTING STARTED

1.1.2 INSPECTION CHECKLIST

Unwrap the relay and inspect the relay for physical damage.

Verify that the model on the label on the side of the relay matches the model ordered.

Figure 1–4: IDENTIFICATION LABEL (A4455P6)

Default Chapter2
- Table of Contents2
1 Getting Started10
- Important Procedures10
- Overview17
- Enervista 650 Setup Software21
- Hardware27
2 Product Description30
- Overview30
- Ordering Code33
- Technical Specifications35
- External Connections60
3 Hardware62
- Module Description62
- Power Supply63
- Mechanical Description64
  - Mounting64
  - Rear Description67
- Wiring71
4 Human Interfaces74
- Introduction74
- Values74
5 Settings148
- Overview148
  - Setting Main Menu148
- Product Setup150
- System Setup168
- Protection Elements178
- Control Elements333
- Metering351
- Inputs / Outputs358
- Records365
7 Iec 61850 Protocol370
- Iec61850 Generic Substation State Event (Gsse)370
- Iec 61850 Profile for F650375
- Iec 61850 Configurator429
  - Overview429
  - Iec 61850 Configurator Tool429
8 Security458
- Adding Users458
  - User Rights458
- Changing Passwords459
- Enabling Security460
- Loging into Enervista 650 Setup461
  - Introduction462
  - Firmware Upgrade475
9 Communication Parameters462
- Summary of Main Steps485
  - Boot Code Upgrade (*)485
  - Firmware Upgrade (*)485
10 Commissioning486
- Visual Inspection486
- Out of Service Setting487
- General Considerations on the Power Supply Network488
- Isolation Tests489
- Indicators490
- Power Supply Testing491
- Communications492
- Verification of Measurement493
- Inputs and Outputs496
- Connections for Testing Protection Elements498
- Instantaneous Overcurrent (50Ph, 50Pl, 50N, 50G y 50Sg)499
- Time Overcurrent (51Ph, 51Pl, 51N, 51G and 46)500
- Directional Elements (67P, 67N, 67G, 67Sg)501
- Undervoltage Elements (27P, 27X)505
  - Element505
- Overvoltage Elements (59P, 59X, 59Nh, 59Nl, 47)506
- Frequency Elements (81O/81U)509
- Recloser510
- Thermal Image Element512
11 Application Examples514
- Example 1: Communication & Protection Settings Procedure514
- Example 2: Toc Protection + Reclosing Settings Procedure518
- Example 3: Procedure to Set an Operation521
  - Description of the Exercise521
    - Procedure521
  - Test523
12 Frequently Asked524
- Communications524
- Protection526
- Control and Hmi527
- Relay Configuration528
- Symptoms and Recommended Actions530
Logic Operands534
Access to F650 Data570
Modbus F650571
- Functions Used571
- Physical Layer571
- B.2.1 Functions Used571
- Data Link Layer572
- Generic Reading573
- B.2.4 Generic Reading573
- Generic Writing574
- B.2.5 Generic Writing574
- Function Codes575
- Exceptions and Error Responds575
- B.2.6 Function Codes575
Modbus Appendix577
- Data Management577
- Writing Settings577
- Snapshot Events577
- B.4.1 Data Management577
- Operations581
- B.4.4 Operations581
Output Writing583
- Control Events583
- B.5.1 Control Events583
- Event Structure584
- B.5.2 Event Structure584
Events Status Request(Alarms)586
- Control Events Retrieval from the Command Line586
- Serial Comunication586
- Ethernet Communication586
- Acknowledgement of Events (Alarms587
- Virtual Inputs Writing587
- User Map587
- Retrieving Oscilography588
- Time Synchronization588
  - B.6.7 Retrieving Oscilography588
  - B.6.9 Enqueueing Messages589
- B.6.11 Modbus Check Function590
Binary Input Points721
Dnp Configuration Examples723
- Configuring Dnp User Map723
- Example of Custom Binary Input Points Map725
- Multiple Dnp 3.0 Masters Communication with F650727
- Interoperability Document746
- F.1.1 Interoperability Document746
- Application Level752
- F.1.2 Application Level752

Other manuals for GE F650

User Guide323 pages

Questions and Answers:

Need help?

Do you have a question about the GE F650 and is the answer not in the manual?

GE F650 Specifications

General

Model	F650
Category	Controller
Frequency	50/60 Hz
Display	LCD
Type	Feeder Protection Relay
Application	Feeder Protection and Control
Communication Protocols	DNP3, Modbus, IEC 61850
Protection Functions	Overcurrent, Earth Fault
Manufacturer	General Electric
Input Voltage	24-250 VDC/VAC