To Next Page

To Previous Page

T60 Transformer Protection System UR Series Instruction Manual revision 7.2x.

FlexLogic, FlexElement, FlexCurve, FlexAnalog, FlexInteger, FlexState, EnerVista,

CyberSentry, HardFiber, Digital Energy, Multilin, and GE Multilin are trademarks

or registered trademarks of GE Multilin Inc.

The contents of this manual are the property of GE Multilin Inc. This

documentation is furnished on license and may not be reproduced in whole or in

part without the permission of GE Multilin. The content of this manual is for

informational use only and is subject to change without notice.

Part number: 1601-0090-AA2 (December 2014)

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
- Ur Overview13
- Enervista Ur Setup Software15
- Ur Hardware27
- Using the Relay28
2 Product Description31
- Introduction31
- Specifications50
3 Hardware65
- Panel Cutout65
  - Horizontal Units65
  - T60 Horizontal Dimensions (Enhanced Panel)65
- Description65
- Direct Input/Output Communications89
4 Human Interfaces105
- Enervista Ur Setup Software Interface105
- Extended Enervista Ur Setup Features108
- Faceplate Interface117
5 Settings132
- Changing Existing Password133
- Invalid Password Entry133
- Overview135
- Settings Menu135
- Product Setup142
- System Setup236
- Grouped Elements314
- Control Elements403
- Inputs and Outputs444
- Transducer Inputs and Outputs462
- Testing472
- Overview477
- Status477
- Records504
- Product Information507
  - Model Information507
  - Firmware Revisions507
7 Commands and509
- Commands509
- Targets514
- Differential Characteristic Test521
- Minimum Pickup521
8 Commissioning521
- Description521
  - Slope 1 / Breakpoint 1522
  - Differential Restraint Characteristic522
- Differential Characteristic Test Examples523
- Frequency Element Tests535
- Commissioning Test Tables537
9 Maintenance539
- Replace Battery541
  - Replace Battery for Rh/Rl Power Supply541
  - Battery Location on Rh/Rl Power Supply Module541
- Batteries541
Parameter Lists547
- A.1.1 Flexanalog Items547
- A.1.2 Flexinteger Items571
- Flexinteger Items571
Modbus Communications573
Modbus Rtu Protocol573
- Physical Layer573
- Data Link Layer573
- Introduction573
- B.1.1 Introduction573
- Modbus Rtu Crc-16 Algorithm574
- Modbus Tcp/Ip Format574
Modbus Function Codes576
- Supported Function Codes576
- Read Actual Values or Settings (Function Code 03/04H576
- Exception Responses578
File Transfers580
Memory Mapping581
- Modbus Memory Map581
- Data Formats655
Iec 61850693
Overview693
- Introduction693
- C.1.2 Communication Profiles693
Server Data Organization694
- Ggio1: Digital Status Values694
- Ggio2: Digital Control Values694
- Ggio3: Digital Status and Analog Values from Goose Data694
  - Overview694
- Ggio4: Generic Analog Measured Values694
- C.2.1 Overview694
- Mmxu: Analog Measured Values695
- Protection and Other Logical Nodes695
Server Features and Configuration697
- Buffered/Unbuffered Reporting697
- File Transfer697
- Timestamps and Scanning697
- Logical Device Name697
- Location697
- Logical Node Name Prefixes698
- Connection Timing698
- Non-Iec 61850 Data698
- Communication Software Utilities698
Generic Substation Event Services: Gsse and Goose699
- Gsse Configuration699
- Fixed Goose699
- Configurable Goose699
- C.4.1 Overview699
- Ethernet Mac Address for Gsse/Goose702
- Gsse ID and Goose ID Settings702
Iec 61850 Implementation Via Enervista Ur Setup703
- Overview703
- C.5.1 Overview703
- Configuring Iec 61850 Settings704
- About ICD Files705
- Creating an ICD File with Enervista Ur Setup709
- About Scd Files709
- Importing an Scd File with Enervista Ur Setup712
- Scd File Structure, Ied Node712
Acsi Conformance714
- Acsi Basic Conformance Statement714
- Acsi Models Conformance Statement714
- Acsi Services Conformance Statement715
  - Logical Nodes Table718
Iec 60870-5-103723
- Overview723
  - D.1.2 Factor and Offset Calculation to Transmit Measurand723
  - D.1.3 Interoperability Document724
Iec 60870-5-104 Protocol729
- Interoperability Document729
- Point List737
- E.1.2 Point List737
Device Profile Document739
- Dnp V3.00 Device Profile739
  - Requires Application Layer Confirmation740
  - F.1.2 Implementation Table742
Dnp Point Lists746
- Binary Input Points746
- Binary and Control Relay Output747
  - F.2.3 Counters748
  - F.2.4 Analog Inputs749
Radius Server Configuration751
Change Notes753
- H.1.1 Revision History753
- Changes to the T60 Manual754
Warranty760
- Ge Multilin Warranty760
- H.3.1 Ge Multilin Warranty760
Index761

Frequency	50/60 Hz
Mounting	Panel Mount
Protection Functions	Overcurrent
Communication Protocols	DNP3
Operating Temperature	+70°C
Enclosure	IP54 (front panel)

GE T60 User Manual

Table of Contents

Questions and Answers:

GE T60 Specifications

Related product manuals