gefran ADV200 Functions Description And Parameters List

ADV200 • Functions description and parameters list 155
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
23.8.6 5714FLfaultenablesrc LINK 16 6002 0 16384 ERW FVS
This parameter is used to select the origin (source) of the FLfaultenable signal.
The signal to be associated with this function can be selected from the “L_DIGSEL1” selection list.
0 FLfaultenable not active (No FastLink alarm signal)
1 FLfaultenable active (FastLink alarm signal)
When the drive detects a FastLink fault, it prepares to trigger a “FastLink fault” alarm.
This command is used to select whether an alarm is generated when a fault is detected.
Alarm generation is enabled in the default conguration.
The conguration of the “FLfaultenablesrc” parameter can be changed to control the phases in which alarm
generation is enabled.
For example, by connecting the “FLfaultenablesrc” parameter to “Enablestatemon” you can enable gen-
eration of the “FastLink fault” alarm in the phase when the drive is enabled.
In systems where drive the drives are not powered-off simultaneously, some drives detect a FastLink fault and
generate a FastLink alarm.
This parameter is used to disable the alarm at power-off by connecting the “FLfaultenablesrc” parameter to
“Enablestatemon”.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
23.8.7 5730FLFwd1src LINK 16/32BIT 6000 0 16384 ERW FVS
23.8.8 5732FLFwd2src  LINK 16/32BIT 6000 0 16384 ERW FVS
23.8.9 5734FLFwd3src LINK 16/32BIT 6000 0 16384 ERW FVS
23.8.10 5736FLFwd4src LINK 16/32BIT 6000 0 16384 ERW FVS
This parameter is used to select the origin (source) of the FLFw1src signal.
The signal to be associated with this function can be selected from the “L_FLWORD” selection list.
On the drive congured as the master, these parameters are used to select the data to be sent to the rst
slave.
On drives congured as slaves, these paramters are used to select the data that the slave must include in the
data frame to replace the data received from the previous drive.
Replacement is disabled in the default conguration. It can be enabled with the PAR 5712 “FLNFwdslave
chg“ parameter.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
23.8.11 5830FLRev1src LINK 16/32BIT 6000 0 16384 ERW FVS
23.8.12 5832FLRev2src LINK 16/32BIT 6000 0 16384 ERW FVS
Parameter signicant only for Slave drive, indicates what data to insert in rst word to be sent to Master drive
when Slave is interrogated. Selectable values are shown on the L_FLWORD list.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
23.8.13 5750FLFwd1mon INT32 32BIT 0 0 2^32 ER FVS
23.8.14 5752FLFwd2mon INT32 32BIT 0 0 2^32 ER FVS
23.8.15 5754FLFwd3mon INT32 32BIT 0 0 2^32 ER FVS
23.8.16 5756FLFwd4mon INT32 32BIT 0 0 2^32 ER FVS
23.8.17 5758FLFwd5mon INT32 32BIT 0 0 2^32 ER FVS
23.8.18 5760FLFwd6mon INT32 32BIT 0 0 2^32 ER FVS
23.8.19 5762FLFwd7mon INT32 32BIT 0 0 2^32 ER FVS
23.8.20 5764FLFwd8mon INT32 32BIT 0 0 2^32 ER FVS
These parameters are not used on the master drive.
On the slave drive these parameters show the value received from the previous drive. The “Inv” parameters en-
able the value received to be used with the opposite sign, without changing any of the data sent to subsequent
slaves.

gefran ADV200 Specifications

General

Brand	gefran
Model	ADV200
Category	Inverter
Language	English