What to do if my Goodwe DNS displays 'Fac Failure'?
If your Goodwe inverter is showing a 'Fac Failure', verify the following: 1. The inverter is connected to the grid. 2. The power grid is connected to the cable. 3. The power grid is available.
What to do if my Goodwe DNS displays 'AFCI-Fault'?
If your Goodwe Inverter is showing an 'AFCI-Fault', here are steps you can take: 1. Turn off the DC switch of the inverter. 2. Make sure the DC connector is the correct model and is properly connected. 3. Turn on the DC switch and ensure it is connected correctly. 4. If the problem persists, contact your local service office for further assistance.
Why does my Goodwe DNS have no display?
If your Goodwe inverter's display is not working, try these steps: 1. Turn off the DC switch and unplug the DC connector, then measure the voltage of the PV array. 2. Plug in the DC connector and turn on the DC switch. 3. If the PV array voltage is lower than 250V, check the configuration of the inverter module. 4. If the voltage is higher than 250V, contact your local service office for assistance.
What to do if my Goodwe DNS shows a Vac Failure?
If your Goodwe Inverter displays a Vac Failure, it means there's an issue with the grid voltage. First, the inverter will automatically restart within 5 minutes if the grid returns to normal. Ensure the grid voltage conforms to the specified requirements. Also, verify that the neutral (N) wire and PE cable are securely connected.
What to do if my Goodwe DNS displays 'Ground I Failure'?
If your Goodwe inverter reports a 'Ground I Failure' because the ground current is too high, follow these steps: 1. Unplug the inputs from the PV generator and inspect the peripheral AC system. 2. After resolving the issue, reconnect the PV panel and check the inverter status. 3. If the problem continues, contact your local service office for assistance.
What to do if my Goodwe DNS displays 'Utility Loss'?
If your Goodwe inverter indicates a 'Utility Loss', please check the following: 1. Ensure the inverter is properly connected to the power grid. 2. Verify that the power grid is connected to the cable. 3. Confirm the availability of the power grid.
What to do if my Goodwe DNS displays 'Vac Failure'?
If your Goodwe inverter is showing a 'Vac Failure', here are some things to check: 1. The PV Inverter will automatically restart within 5 minutes if the grid returns to normal. 2. Ensure that the grid voltage conforms to the specified requirements. 3. Verify that the neutral (N) wire and PE cable are properly connected. 4. If the problem persists, contact your local service office for further assistance.
What to do if my Goodwe DNS Inverter shows 'Isolation Failure'?
If your Goodwe inverter displays an 'Isolation Failure', follow these steps: 1. Check the impedance between the ground and PV (+) & PV (-). The impedance value must be greater than 100kΩ. Ensure the inverter is properly grounded. 2. If the problem persists, contact your local service office for assistance. Additionally, the inverter has a built-in buzzer that will sound continuously for 1 minute upon failure. If the fault isn't resolved, the buzzer will sound every 30 minutes. You can also add the inverter to a monitoring platform and set up alarm reminders to receive email notifications about alarm information.
What to do if my Goodwe Inverter has no display?
If your Goodwe Inverter's display is not working: 1. Turn off the DC switch and unplug the DC connector, then measure the voltage of the PV array. 2. Plug in the DC connector and turn on the DC switch. 3. If the PV array voltage is lower than 250V, check the configuration of the inverter module.
What does Ground I Failure mean on Goodwe Inverter, and how can it be fixed?
A 'Ground I Failure' on your Goodwe Inverter indicates that the ground current is too high. Unplug the inputs from the PV generator and check the peripheral AC system. Once the problem is resolved, reconnect the PV panel and check the inverter status.
General| Max. Efficiency | 97.8% |
|---|---|
| MPPT Efficiency | 99.9% |
| Cooling Method | Natural Convection |
| Protection Rating | IP65 |
| Start Voltage | 80 V |
| Nominal AC Voltage | 230 V |
| THDi | <3% |
| Number of MPPTs | 2 |
| Output Voltage | 230 V |
| Frequency | 50 Hz / 60 Hz |
| Type | Grid-Tied Inverter |
| Rated Power Output | 3000W, 3600W, 4200W, 5000W |
| Communication | RS485 |
| Max. DC Input Power | 4500W, 5400W, 6300W, 7500W |
| Max. DC Voltage | 550V |
| MPPT Voltage Range | 80-500V |
| Rated AC Output Power | 3000W, 3600W, 4200W, 5000W |
| AC Voltage Range | 180V - 280V |
| Power Factor | 0.8 leading to 0.8 lagging |
| Operating Temperature Range | -25°C to 60°C |
| MPPT Range | 80-500V |
| Model | DNS Series |
Lists the specific inverter models covered by this manual.
Identifies the intended readers and required expertise for this manual.
Covers overall safety instructions and warnings for operating the inverter.
Specific safety measures for the DC input side of the inverter.
Specific safety measures for the AC output side of the inverter.
Safety precautions related to the physical installation of the inverter unit.
Guidelines on personal protective equipment and qualifications for personnel.
States compliance with relevant EU directives for the inverter.
Describes the intended use and context for the PV inverter.
Details the different grid connection types the inverter supports.
Overview of the inverter's external features.
Identifies and describes the various parts of the inverter.
Provides physical measurements and key dimensions of the inverter.
Explains the function and status indicated by the inverter's LED lights.
Details the information found on the inverter's identification nameplate.
Steps to follow when checking the product before accepting delivery.
Lists all items included in the product package.
Recommendations for proper storage of the inverter if not immediately installed.
Specifies the conditions and location requirements for installing the inverter.
Covers requirements for mounting supports and acceptable installation angles.
Lists the tools recommended for performing the inverter installation.
Step-by-step guide on how to physically install the inverter unit.
Critical safety instructions before making any electrical connections.
Instructions for correctly connecting the protective earth (PE) cable.
Steps for connecting the DC power input from the PV array.
Detailed procedure for preparing and connecting DC input cables.
Instructions for connecting the AC power output to the grid.
Details on connecting various AC output connector types (AC-1, AC-2, AC-3).
Guide for connecting communication cables for monitoring and control.
Checklist of items to verify before powering on the equipment.
Step-by-step procedure for safely powering on the inverter.
Explains the status indicators and control buttons on the inverter.
Guides users on configuring inverter settings using the LCD screen.
Detailed descriptions of various inverter parameters and their functions.
Steps for updating the inverter's firmware using a USB flash drive.
Instructions for setting parameters using the mobile SolarGo application.
Information on using the SEMS portal for system monitoring and management.
Procedure for safely shutting down the inverter before maintenance.
Steps for safely disconnecting and removing the inverter from its mounting.
Information on environmentally responsible disposal of the inverter.
Guidance on identifying and resolving common inverter faults and issues.
Recommended periodic maintenance tasks and their frequency.
To Next Page
