What causes 'PV Over Voltage' on a Goodwe HT Inverter and how to fix it?
The 'PV Over Voltage' error on your Goodwe Inverter means that too many PV modules are connected in series, causing the open-circuit voltage to exceed the operating voltage. Check if the PV string input voltage matches the value displayed on the LCD. Also, verify that the PV string voltage meets the maximum input voltage requirements.
How to fix an 'Over Temperature' error on a Goodwe HT?
If your Goodwe Inverter is showing an 'Over Temperature' error, it may be installed in a location with poor ventilation, the ambient temperature might be exceeding 60°C, or there could be a fault with the internal fan. Check the ventilation and ambient temperature around the installation point. If ventilation is poor or the temperature is too high, improve the ventilation and heat dissipation. If both are normal, it may indicate a need to contact support.
What causes a Vac Failure on a Goodwe Inverter?
A 'Vac Failure' on your Goodwe Inverter indicates that the utility grid voltage is outside the allowed range. To resolve this, ensure that the grid voltage is within the permissible limits and that the phase sequence of the AC cables are correctly connected, and the PE cable is properly and firmly connected.
What does ISO Fail mean on a Goodwe Inverter?
An 'ISO Fail' error on your Goodwe Inverter suggests that the PV system is short-circuited to the ground or is in a moist environment with poor insulation. Check the PV input cables for any breaks, ensure the module frames and metal bracket are securely grounded, and verify that the AC side is properly grounded.
What does 'Ground I Fail' mean on my Goodwe Inverter, and how can I resolve it?
The 'Ground I Fail' error on your Goodwe Inverter indicates that the input insulation impedance to the ground decreases during operation. Check if the inverter's working environment meets the requirements; for instance, high humidity on rainy days can cause this issue. Also, ensure that the components are properly grounded, and the AC side is correctly grounded.
What does 'DC Bus High' mean on a Goodwe Inverter, and how do I fix it?
The 'DC Bus High' error on your Goodwe Inverter usually indicates an internal fault. Make sure that the software is the latest version. Restart the inverter to check whether it can work properly.
What does 'Night BUS Fault' mean on my Goodwe Inverter?
If your Goodwe Inverter displays the 'Night BUS Fault' message, it means there is a problem with the utility grid power or the AC cable is disconnected, or the AC breaker is off. To attempt a fix, disconnect the AC output switch and DC input switch, wait 5 minutes, then reconnect them. If the issue persists, contact your dealer or after-sales service.
What to do if my Goodwe HT Inverter displays 'DC-SPD'?
If your Goodwe Inverter shows 'DC-SPD', it indicates that the inverter was struck by lightning. As a first step, improve the lightning protection around the inverter. Then, disconnect the AC output switch and the DC input switch, wait 5 minutes, and reconnect them. If the problem continues after these steps, contact your dealer or after-sales service.
What causes SPI Comm Fail on Goodwe HT?
A 'SPI Comm Fail' error on your Goodwe Inverter could be due to the chip not being powered on or a wrong chip program version. Disconnect the AC output switch and DC input switch, then reconnect them after 5 minutes. If the problem persists, further assistance may be needed.
What causes an ExFan Failure on a Goodwe Inverter?
An 'ExFan Failure' on your Goodwe Inverter can be due to an abnormal fan power supply, a mechanical issue, or the fan aging and becoming damaged. Disconnect the AC output switch and DC input switch, then connect them again after 5 minutes. If the problem continues, further assistance may be needed.
Lists supported inverter models with their power and voltage ratings.
Specifies that the manual is for trained and knowledgeable technical professionals.
Explains the meaning of different hazard levels (Danger, Warning, Caution, Notice) used in the manual.
Lists version history and updates for the manual.
Provides general safety guidelines and precautions for using the inverter.
Details safety precautions related to the DC side of the inverter.
Details safety precautions related to the AC side of the inverter.
Covers safety precautions specifically for the installation of the inverter.
Outlines the necessary qualifications and training for personnel handling the equipment.
Describes the intended use of the HT inverter as a three-phase PV string grid-tied inverter.
Presents the circuit diagrams for different HT inverter models.
Illustrates the various grid structures (TN-S, TN-C, TT, IT) supported by the inverters.
Details the physical components and layout of the inverter.
Lists items to check before accepting the product from the supplier.
Shows all the items included in the product package.
Provides guidelines for storing the inverter safely and appropriately.
Details environmental and location requirements for inverter installation.
Step-by-step guide for physically installing the inverter.
Essential safety rules to follow during electrical connections.
Steps for connecting the DC input cables from the PV array.
Guide for connecting the AC output power cable.
How to connect communication cables for data logging and monitoring.
Checklist of items to verify before powering on the inverter.
Step-by-step guide on how to safely power on the inverter.
Explains the inverter's indicators and buttons for system status.
Guide for configuring inverter settings using the LCD interface.
Instructions for setting inverter parameters using a mobile application.
How to monitor inverter performance and status using the SEMS portal.
Steps to safely power off the inverter before performing maintenance.
Procedures for safely detaching the inverter from its mounting.
Guidelines for the proper disposal of the inverter according to regulations.
Common faults, their causes, and suggested solutions for the inverter.
Schedule and methods for regular maintenance tasks.
Specifications related to the inverter's DC input characteristics.
Specifications related to the inverter's AC output characteristics.
Details on the maximum and European efficiency ratings of the inverter.
Lists various integrated and optional protection features of the inverter.
General specifications like temperature range, humidity, and altitude.
General| Max DC Input Voltage | 1100V |
|---|---|
| MPPT Voltage Range | 200-1000V |
| Max AC Output Power | 3.6kW to 10kW |
| Number of MPPTs | 1 or 2 |
| Max PV Input Voltage | 1100V |
| MPPT Range | 200-1000V |
| AC Output Frequency | 50/60Hz |
| Communication | RS485, Ethernet |
| Operating Temperature Range | -25°C to 60°C |
| Protection Level | IP65 |
To Next Page
