GSi TopDry Terminal 24

Questions and Answers

S
Susan ParkerSep 4, 2025
What causes 'Heater 2 Gas Vapor Temp Hi-Limit' error on GSi Touch terminals?
- L
  Lisa RiceSep 4, 2025
  The 'Heater 2 Gas Vapor Temp Hi-Limit' error on your GSi Touch terminals indicates that the LP gas vapor temperature sensor located in the gas pipe downstream from the vaporizer coil on fan and heater #2 has opened, meaning the vaporizer coil is running too hot. Adjust the vaporizer by loosening the bolt and moving it away from the flame. The sensor automatically resets itself.
A
annallenAug 25, 2025
What to do if the GSi Touch terminals display 'Drying Chamber Overflow Switch Tripped'?
- A
  Ashley BrownAug 25, 2025
  If you see 'Drying Chamber Overflow Switch Tripped' on your GSi Touch terminals, it means the grain level in the drying chamber has reached the Drying Chamber Overflow switch. You'll need to dump grain from the drying chamber before restarting the dryer. Also, lower the High Level switch delay setting.
M
Malik WhiteAug 25, 2025
What does it mean when GSi Touch terminals says 'Wet Grain Supply Empty. Add grain to Wet Tank or disable Wet Tank Switch on Setup Menu to continue.'?
- R
  Rebecca RyanAug 26, 2025
  This message on your GSi Touch terminals indicates that the optional Wet Supply Switch delay timer has timed out, meaning the wet supply tank is low on grain. You should add grain to the Wet Tank or disable the Wet Tank Switch on the Setup Menu to continue.
E
Erin MarshSep 12, 2025
What does 'Out of Grain Timer Expired - Cooling Down' mean on GSi Touch terminals?
- A
  Ashley Ramirez MDSep 12, 2025
  This message on your GSi Touch terminals means that either the dryer is out of grain or the fill system is filling too slowly, and the dryer will go to cool down mode.
M
Melissa JacobsSep 22, 2025
What does Heater 1 Air Flow Lost mean on my GSi TopDry Terminal 24 Control Panel?
- B
  Bryan ShieldsSep 22, 2025
  If Heater 1 Air Flow is Lost on your GSi Control Panel, the air switch located in the fan #1 electrical box has opened after initially closing. The air switch needs adjustment or airflow to or from fan #1 is being restricted.
L
luis58Sep 8, 2025
What does 'Plenum Temp Sensor Open' mean on GSi Touch terminals?
- D
  dhunterSep 8, 2025
  If your GSi Touch terminals display 'Plenum Temp Sensor Open', it means the controller sees an open electrical connection to the plenum temperature sensor. Check the wiring or replace the sensor.
F
fosterlisaSep 1, 2025
How to fix 'Aeration Fan 2 Motor Overload' on GSi Touch terminals?
- C
  Cynthia DouglasSep 1, 2025
  The 'Aeration Fan 2 Motor Overload' message on your GSi Touch terminals indicates that the thermal overload for Aeration Fan #2, located in the fill box, has tripped, indicating an over-current condition. The overload must be reset manually.
I
iloveSep 23, 2025
What to do if Heater 1 Fan Contactor Aux Contacts are Stuck Closed on my GSi TopDry Terminal 24?
- Q
  qbowmanSep 23, 2025
  If the Heater 1 Fan Contactor Aux Contacts are Stuck Closed on your GSi Control Panel, check to see if the starter contacts are stuck closed or if the starter is staying engaged after.
M
Mary PruittSep 15, 2025
What to do if the Heater 1 Gas Pressure is out of range on my GSi TopDry Terminal 24?
- I
  Ian LambSep 15, 2025
  If the Heater 1 Gas Pressure is out of range on your GSi Control Panel, it means the optional gas pressure switch on heater #1 fuel train has opened. Reduce the gas pressure to resolve this.
T
Travis BoydAug 28, 2025
How to resolve 'Heater 1 Heater Ignition Failure' on GSi Touch terminals?
- M
  Mark ReedAug 28, 2025
  If your GSi Touch terminals display 'Heater 1 Heater Ignition Failure', it means Heater #1 failed to light during the ignition period. This could be due to several reasons: 1. The heater failed to light. 2. The flame sensor needs adjustment. Bend the flame sensor so that it is in the flame. If the heater isn't lighting, verify that the dryer is getting fuel, all solenoids are opening, and the ignitor is sparking.