What causes 'Heater 1 Heater Flame Lost' on GSi Touch terminals and how to fix it?
If your GSi Touch terminals display 'Heater 1 Heater Flame Lost', it indicates that Heater #1 lost flame after initially lighting. Adjust the flame sensor so that it is in the flame. Also, ensure that the dryer isn't running out of fuel.
How to resolve 'Heater 2 Heater Ignition Failure' on GSi Touch terminals?
If your GSi Touch terminals display 'Heater 2 Heater Ignition Failure', it means Heater #2 failed to light during the ignition period. This could be due to several reasons: 1. The heater failed to light. 2. The flame sensor needs adjustment. Bend the flame sensor so that it is in the flame. If the heater isn't lighting, verify that the dryer is getting fuel, all solenoids are opening, and the ignitor is sparking.
How to resolve 'Heater 1 Heater Ignition Failure' on GSi Touch terminals?
If your GSi Touch terminals display 'Heater 1 Heater Ignition Failure', it means Heater #1 failed to light during the ignition period. This could be due to several reasons: 1. The heater failed to light. 2. The flame sensor needs adjustment. Bend the flame sensor so that it is in the flame. If the heater isn't lighting, verify that the dryer is getting fuel, all solenoids are opening, and the ignitor is sparking.
What does 'Plenum Temp Sensor Shorted' mean on GSi Touch terminals?
If your GSi Touch terminals display 'Plenum Temp Sensor Shorted', it means the controller sees a shorted electrical connection to the plenum temperature sensor. Check the wiring or replace the sensor.
What does 'Out of Grain Timer Expired - Cooling Down' mean on GSi Touch terminals?
This message on your GSi Touch terminals means that either the dryer is out of grain or the fill system is filling too slowly, and the dryer will go to cool down mode.
What to do if Heater 2 on my GSi Control Panel loses flame?
If Heater #2 loses flame after initially lighting on your GSi Control Panel, adjust the flame sensor, so that it is in the flame. Make sure that the dryer is not running out of fuel.
What does it mean when GSi Touch terminals says 'Drying Chamber Low Level Switch Exposed'?
This message on your GSi Touch terminals means that the Low Level Switch delay timer has timed out, indicating the dryer is low on grain. This can happen if the dryer is out of wet grain or filling too slowly.
What does it mean when GSi Touch terminals says 'Grain Temp Sensor to Sensor Max Differential Exceeded. Check status of Grain Temp Sensors.'?
This message on your GSi Touch terminals means that the difference between the individual grain temperature sensors has exceeded the value set for the Max Grain Sensor Differential in the Temperature Menu. Check for plugged dump chutes or trash buildup in the drying chamber.
What to do if my GSi Touch terminals display 'Analog Grain Temp Hi-Limit Tripped'?
If your GSi Touch terminals display 'Analog Grain Temp Hi-Limit Tripped', it means the grain temperature has exceeded the Plenum Grain Temp setpoint entered on the Temperature Menu. Check for plugged dump chutes or over-dried grain.
What does it mean when GSi Touch terminals says 'Wet Grain Supply Empty. Add grain to Wet Tank or disable Wet Tank Switch on Setup Menu to continue.'?
This message on your GSi Touch terminals indicates that the optional Wet Supply Switch delay timer has timed out, meaning the wet supply tank is low on grain. You should add grain to the Wet Tank or disable the Wet Tank Switch on the Setup Menu to continue.
General| Brand | GSi |
|---|---|
| Model | TopDry Terminal 24 |
| Category | Control Panel |
| Connectivity | Ethernet |
| Ports | Ethernet |
| Operating Temperature | 0°C to 40°C |
| Humidity | non-condensing |
General rules for safe operation and maintenance.
Explains symbols used for hazards, warnings, and notices.
Details on personal protective equipment and general safety instructions.
Describes the basic function and components of the dryer.
Overview of the control panel's buttons, switches, and touchscreen.
Essential checks before initial dryer startup.
Critical steps for immediate shutdown.
Step-by-step guide for the first startup of the dryer.
Lists common error messages and their causes/remedies.
To Next Page