What does it mean if Heater 1 Fan Contactor Aux Contacts Failed to Close on my GSi TopDry Terminal 24 Control Panel?
If the Heater 1 Fan Contactor Aux Contacts Failed to Close on your GSi Control Panel, it means the auxiliary contacts on the fan #1 motor starter failed to close when the starter was energized. Check that starter #1 is pulling in when energized.
What does it mean if Heater 2 Fan Contactor Aux Contacts Failed to Close on my GSi Control Panel?
If the Heater 2 Fan Contactor Aux Contacts Failed to Close on your GSi Control Panel, the auxiliary contacts on the fan #2 motor starter failed to close when the starter was energized. Check that starter #1 is pulling in when energized.
What to do if Heater 1 Fan Contactor Aux Contacts are Stuck Closed on my GSi TopDry Terminal 24?
If the Heater 1 Fan Contactor Aux Contacts are Stuck Closed on your GSi Control Panel, check to see if the starter contacts are stuck closed or if the starter is staying engaged after.
How to fix 'Aeration Fan 1 Motor Overload' on GSi Touch terminals?
The 'Aeration Fan 1 Motor Overload' message on your GSi Touch terminals indicates that the thermal overload for Aeration Fan #1, located in the fill box, has tripped, indicating an over-current condition. The overload must be reset manually.
What to do if the GSi Touch terminals display 'Drying Chamber Overflow Switch Tripped'?
If you see 'Drying Chamber Overflow Switch Tripped' on your GSi Touch terminals, it means the grain level in the drying chamber has reached the Drying Chamber Overflow switch. You'll need to dump grain from the drying chamber before restarting the dryer. Also, lower the High Level switch delay setting.
What does it mean when GSi Touch terminals says 'Wet Grain Supply Empty. Add grain to Wet Tank or disable Wet Tank Switch on Setup Menu to continue.'?
This message on your GSi Touch terminals indicates that the optional Wet Supply Switch delay timer has timed out, meaning the wet supply tank is low on grain. You should add grain to the Wet Tank or disable the Wet Tank Switch on the Setup Menu to continue.
What to do if my GSi Touch terminals display 'Analog Grain Temp Hi-Limit Tripped'?
If your GSi Touch terminals display 'Analog Grain Temp Hi-Limit Tripped', it means the grain temperature has exceeded the Plenum Grain Temp setpoint entered on the Temperature Menu. Check for plugged dump chutes or over-dried grain.
What does it mean when GSi Touch terminals says 'Grain Temp Sensor to Sensor Max Differential Exceeded. Check status of Grain Temp Sensors.'?
This message on your GSi Touch terminals means that the difference between the individual grain temperature sensors has exceeded the value set for the Max Grain Sensor Differential in the Temperature Menu. Check for plugged dump chutes or trash buildup in the drying chamber.
What does it mean when GSi Touch terminals says 'Drying Chamber Low Level Switch Exposed'?
This message on your GSi Touch terminals means that the Low Level Switch delay timer has timed out, indicating the dryer is low on grain. This can happen if the dryer is out of wet grain or filling too slowly.
What to do if the GSi Touch terminals display 'Storage Chamber is Full - Cooling Down'?
If your GSi Touch terminals show 'Storage Chamber is Full - Cooling Down', it means the grain level in the storage chamber has reached the storage chamber level switches, indicating that the storage chamber is full. You'll need to remove grain from the storage chamber before restarting the dryer. The dryer will go to cool down mode.
General| Brand | GSi |
|---|---|
| Model | TopDry Terminal 24 |
| Category | Control Panel |
| Connectivity | Ethernet |
| Ports | Ethernet |
| Operating Temperature | 0°C to 40°C |
| Humidity | non-condensing |
General rules for safe operation and maintenance.
Explains symbols used for hazards, warnings, and notices.
Details on personal protective equipment and general safety instructions.
Describes the basic function and components of the dryer.
Overview of the control panel's buttons, switches, and touchscreen.
Essential checks before initial dryer startup.
Critical steps for immediate shutdown.
Step-by-step guide for the first startup of the dryer.
Lists common error messages and their causes/remedies.
To Next Page