Honeywell INTELLIGUARD 9000 - Page 25

INTELLIGUARD 9000™
25 74-3047—1
HOLD-UP TEST EVENT LOG
The HOLD-UP TEST Event Lo
g
shows the followin
g
:
NOTE: Each time the same actuator’s buttons are s
q
ueezed
durin
g
a test se
q
uence, an entr
y
is made in the
Event Lo
g
. Therefore, one BIC-2 HU point ma
y
appear more than once in the Event Lo
g
for that test
se
q
uence.
— Point restoral for all of the Hold-up actuators depressed
durin
g
the test
(
text shown in lower case letters
)
.
— End of test
(
text shown in capital letters
)
.
— Alarms of all of the Hold-up actuators depressed durin
g
the
test
(
text shown in capital letters
)
.
— Start of test
(
text shown in capital letters
)
.
2. Enable/Disable CHIME Function
NOTES:
— The CHIME function is onl
y
functional when the
Chime enabled areas are disarmed. No results
are lo
gg
ed.
— The LED located below the CC2 displa
y
blinks
when the Chime is activated. Therefore, the CC2
provides both audible and visual notification of an
event, whereas the KID notification is onl
y
audi-
ble.
1.
From the Test menu, select the
2-CHIME
menu.
2.
Press the
ACCEPT
ke
y
. The CC2 displa
y
re
q
uests an
area number.
3.
Enter an area number
(
can be an
y
area from 1 to 8, but
must be an active area
)
. The displa
y
s shows either
CHIME: ENABLED
or
CHIME: DISABLED
.
4.
To chan
g
e the settin
g
, press the
ACCEPT
ke
y
and then
press the scroll down ke
y
one stroke at a time until the
re
q
uired settin
g
is displa
y
ed.
5.
Press the
ACCEPT
ke
y
and the s
y
stem returns to the
2-
CHIME
menu.
6.
Press the scroll ke
y
s or numbers 1, 3 or 4 to move to a
different test menu, return to step 2 to chan
g
e the set-
tin
g
s for other areas, or to
g
o to the next step.
NOTE: When the settin
g
s are made, the
y
remain valid until
chan
g
ed
(
even if
y
ou have exited the test menus
)
.
7.
Open and close the door
(
s
)
associated with the
selected area to verif
y
that the CHIME function works
properl
y
. The CC2 beeps twice and the LED blinks each
time a door
(
defined as point t
y
pe 1
)
is opened.
(
The
beep is heard on an
y
CC2 or KID assi
g
ned to the test
area
)
.
8.
From the CC2, press the
X
ke
y
to exit to the main menu,
Intelliguard 9000
, or press a menu ke
y
.
The followin
g
example explains how the CHIME func-
tion works:
— A s
y
stem has areas 1, 2, 3, 4 and 5 active.
— The CHIME function is enabled for areas 2 and 4.
— Point 2 is pro
g
rammed as door 2 and point 4 is
pro
g
rammed as door 4
(
both as t
y
pe 1
)
.
— Area 2 is armed and area 4 is disarmed.
— When doors 2 and 4 are opened, onl
y
door 4 acti-
vates a chime on the CC2 and/or KID assi
g
ned to
area 4.
— No chime is heard on the CC2 and/or KID
assi
g
ned to area 2 even thou
g
h door 2 was
opened because area 2 is still armed.
— Disarm area 2.
— When a CC2 or KID is assi
g
ned to multiple areas,
such as areas 1, 2 and 4, the chime sounds when
those area doors are opened.
3. WALK-TEST Procedure
1.
Check to see if an
y
points are in alarm.
2.
Make an
y
necessar
y
corrections.
NOTE: All points tested must transition from normal to alarm
and return to normal to be re
g
istered in the Event
Lo
g
.
3.
From the CC2, press the
MODE
ke
y
.
4.
Enter
y
our technician ID and code number
(
00, 9999
)
.
5.
Enter
4
on the CC2 to clear the Event Lo
g
and then
press the
ACCEPT
ke
y
.
6.
Press the
TEST
ke
y
.
7.
Press
3
to select
WALK-TEST
.
8.
Press the
ACCEPT
ke
y
.
9.
Enter the test area number.
WALK-TEST
is displa
y
ed
on the CC2.
10.
Walk throu
g
h the selected area of the buildin
g
(
selected
in previous step
)
and test each alarm input on each
device except the Hold-up actuators. As each point is
tested and
g
oes into alarm, all CC2s assi
g
ned to this
area beep and their LEDs blink to indicate that the
alarms have been received b
y
the I9000.
11.
Restore each alarm input in the area.
(
If red Hold-up
actuators are tested, a manual
Reset Detectors
com-
mand must be made. BIC-2 HU inputs, other than the
red Hold-up actuator, should be tested with the
WALK-
TEST
.
)
NOTE: Actuators defined as Hold-up are not shown as
tested oka
y
in the Event Lo
g
when usin
g
the
WALK
-
TEST
, therefore, it is recommended that the HOLD-
UP TEST procedure be used.
12.
From the CC2, press the
X
ke
y
to end the test. The
I9000 s
y
stem automaticall
y
performs a communication
test
(
COM Test
)
for each device that is associated with
the specified area
(
specified in step 9
)
.
NOTE: When a user ID/pass code other than the techni-
cian’s is used, the communication tests
(
COM Test
)
are not done and the result is not included in the lo
g
.
13.
Press the
MODE
ke
y
.
14.
Press
3
to select
EVENT LOG
.
15.
Press the
ACCEPT
ke
y
to view the Event Lo
g
.
16.
View the results of the test in the Event Lo
g
. See the
Walk Test Event Lo
g
section for an example of the Lo
g
results.
NOTE: When a user ID/pass code other than the techni-
cian’s is used, the communication tests
(
COM Test
)
are not done and the result is not included in the lo
g
.
17.
Repeat steps 5 throu
g
h 16 for each of the pro
g
rammed
areas at the installed site.