Honeywell INTELLIGUARD 9000 - System Test; System Layout and Wiring

INTELLIGUARD 9000™
74-3047—14
Commission
1.
Learn each device.
(
Step 1 can be replaced with steps
a. throu
g
h c.
)
NOTE: A device is
learned
when its address or serial num-
ber is recorded in the CU.
a. Enter the information from Install the S
y
stem sec-
tion, step 5, into the PRO 9000 software
(
Menu:
Pro
g
ram/Pollin
g)
and downloadin
g
the Pollin
g
Table
into the I9000 Control Unit
(
see form no. 74-3046,
Intelli
g
uard 9000 Pro
g
rammer’s Guide for more
information
)
.
b. Before downloadin
g
, set the baud rate for COM 3 to
match the baud rate selected in PRO 9000. Use an
y
CC2 connected to the control unit to set the baud
rate since all CC2s are learned automaticall
y
at
power up.
c. Exit from the CC2 Confi
g
uration Menu for chan
g
es
to become effective. When used with PRO 9000, the
maximum supported baud rate for the I9000 with
EBI Orbix
(
8950-109
)
firmware is 4800 baud.
2.
Check the communication status for each device:
F = COM fail
M = Mar
g
inal
(
latched status, clear with Reset Lo
g
command
)
.
NOTES:
— To view the F and M
(
COM fail and Mar
g
inal
)
,
from the CC2
g
o to the 2-ASSIGN menu
(
sub-
menu of the CONFIGURATION menu, entered b
y
usin
g
the Mode ke
y)
.
— The F and M appear on the far ri
g
ht first line of
text for each device in the table
(y
ou must scroll to
view each device
)
.
— When ever
y
thin
g
is normal, no characters appear
on the far ri
g
ht of the first line of text.
— The
F
(
COM fail
)
clears automaticall
y
when com-
munication is restored to the device exhibitin
g
an
F
.
3.
Disarm each armed area.
4.
Pro
g
ram the tables.
System Test
Perform a
WALK TEST
to make sure all devices with
actuators work properl
y
. This must be done at initial
installation and each time a device is added to or removed
from the s
y
stem.
1.
With all areas disarmed, press
TEST
on the CC2 to
enter the TEST Menu.
2.
Enter
y
our ID and code number.
3.
Press
3
to select
WALK TEST
and press
ACCEPT
.
4.
Select the test area.
5.
Walk throu
g
h the buildin
g
and test each device. A beep
sounds on all CC2s and KIDs assi
g
ned to the test area
as each alarm is tri
gg
ered.
NOTE: When usin
g
the
WALK TEST
, Hold-up Actuators will
not test oka
y
in the Event Lo
g
.
6.
If Hold-up Actuators
(
8003-284, red buttons
)
are tested,
a manual
Reset Detectors
must be made after step 7.
7.
Press
X
to stop the test.
8.
Press
MODE
to enter the MODE Menu.
9.
Press
3
to select
EVENT LOG
.
10.
View the result of each area in the Event Lo
g
to make
sure that each device is respondin
g
as desi
g
ned.
The results of the alarm points tested in the
WALK TEST
are
shown in lower case characters when successfull
y
tested.
NOTE: If the technician ID
(
00
)
and code number
(
9999 =
default value
)
were used in step 2, a communication
test is automaticall
y
performed when the
WALK
TEST
is terminated. The communication test
(
COM
Test
)
results are shown as alarms
(
text in capital let-
ters
)
and indicate proper communication with each
device assi
g
ned to the specified areas.
System Layout and Wiring
The desi
g
ner plans the s
y
stem based on buildin
g
construction
and customer needs. This plan re
q
uires the wirin
g
for the
I9000. The wirin
g
must be routed before mountin
g
an
y
device.
Wirin
g
must be done b
y
a
q
ualified person and must compl
y
with state and local buildin
g
codes.
1.
Map the route for the wires between each device.
2.
With a pencil, li
g
htl
y
mark the mountin
g
locations for
each device.
3.
Install the wirin
g
.
4.
Usin
g
a continuit
y
tester, make sure there are no opens,
wire-to-wire shorts, or wire-to-
g
round shorts before con-
nectin
g
the devices.
Fi
g
. 3 shows a sample wirin
g
plan. See Table 1 for
recommended cable t
y
pes.
Sample Installation Plan
Fi
g
. 4 shows a t
y
pical floor plan with I9000 components in
each room.