Honeywell VISTA-128FBPT - Page 8

8
Program feature or option Permitted in
UL864? Y/N
Possible settings
Settings permitted in UL 864
∗
27 TEST REPORT INTERVAL
Y
Enter 0001-9999 f or t he t est r epor t
interval in hours.
Enter 0000 for t est r epor t i ng.
Must be set to “0024” (M aximum 24
hour s)
∗
28 POWER-UP I N PREV. STATE
Y
0 = disable
1 = enable
M ust be set t o “1” (en abl e).
∗
37 DOWNLOAD COMM AN D
ENABLES
N
0 = disable
1 = enable
M ust be set t o “0” for al l ent r i es
(disable).
∗
41 N ORM AL L Y CL OSED OR
EOLR (ZONES 3-8)
N
0 = E OL R su per vi si on
1 = N.C. loops
M ust be set t o “0” (E OL R
Super vi si on ).
∗
42 DIAL TONE PAUSE
Y
En t er t he w ai t t i m e for di al t one
det ect i on :
0 = 5 seconds; 1 = 11 seconds; 2 = 30
seconds.
M ust be set t o “0” (5 seconds).
∗
44 RI NG DETECTION COUNT
N
En t er 00 t o di sable r i ng det ect i on.
En t er 01-14 for ring counts of 1-14.
En t er 15 t o sel ect An swer i ng
M achi ne Def eat M ode
Must be set to “00” (disable).
∗
56 DYNAMIC SIGNAL DELAY
Y
En t er 00-15 t imes 15 seconds.
M ust be set t o “6” (90 seconds).
∗
77 AUTO TRBL RSTR
Y
0 = disable
1 = enable
M ust be set t o “1” (en abl e).
∗
80 ZONE TYPE 9 -10, 14
RESTORE
N
0 = disable
1 = enable
M ust be set t o “1” (en abl e) for zone
t ype 9.
∗
84 SWI N GER SUPPRESS.
(PARTITION – SPECI FI C)
N
En t er 01-14,
En t er 00 for u nl i m i t ed r epor t s
Must be set to “00” (disable).
1∗
12 PROGRAM N OTI FI CATI ON
Y
0 = no
1 = yes
M ust be set t o “1” (yes).
1∗
13 SYS. SENSOR REV. RELAY
N 0=use nei t her Zone 1 or Zone 2
inputs
1=use Zone 1 i nput ;
2=use Zone 2 i nput ;
3=use Zone 1 and Zone 2 inputs.
N ot U sed. M u st be set t o “0” .
1∗
18 AFFECTS LOBBY
(PARTITION – SPECI FI C)
N
0 = disable
1 = enable
M ust be set t o “0” (di sabl ed) for
par t it ion 1.
1∗
19 ARMS LOBBY (PARTITION
– SPECI FIC)
N
0 = disable
1 = enable
M ust be set t o “0” (di sabl ed) for
par t it ion 1.
1∗
22 thru
1∗
25 CROSS-ZONI N G
PAI RS (1 – 4)
N
Enter 001-250
Enter 000,000 to disable
Must be set to “000,000” (disabled)
for fi r e zon es.
1∗
28 RF TX LOW BATTERY
SOU N D
N
0 = di sar med st at e on l y
1 = bot h ar med and di sar med st at es
Must be set t o “1” (bot h ar med an d
di sar med st at es).
1∗
29 RF TX LOW BATTERY
REPORTI NG
N
0 = disable
1 = enable
M ust be set t o “1” (en abl e).
1∗
30 RF RCVR CH ECK -IN
INTERVAL
N
En t er 02–15 t imes 2 hour s (4–30
hour s)
En t er 00 t o di sable r ecei ver
super visi on
Maxi mum is 02 (4 hour s) for fir e
installations.
1∗
31 RF TX CH ECK -IN
INTERVAL
N
En t er 02–15 t imes 2 hour s (4–30
hour s)
Enter 00 to di sable tr ansmit t er
super visi on
Maxi mum is 02 (4 hours) for fi re
installations.
1∗
35 ACS DLR ENABLES
N 0 = disable
1 = enable
N ot u sed. M ust be set t o “ 0”.
1∗
44 RF KEYPAD TAMPER
DETECTION
N 0 = disable
1 = enable
N ot u sed. M ust be set t o “ 0”.
1∗
45 EXIT DELAY SOUNDING
(PARTITION SPECIFIC)
N
0 = disable
1 = enable
M ust be set t o “0” (di sabl e) for
par t it ion 1.
1∗
48 RF KEYPAD ASSI GN 1-
8=PART. 0=NO
N 0 = none
1-8 = par t i t i on num ber
N ot u sed. M ust be set t o “ 0”.