EasyManuals Logo

HP FlexFabric 5700 series Configuration Guide

HP FlexFabric 5700 series
185 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #153 background imageLoading...
Page #153 background image
146
[SwitchA-Ten-GigabitEthernet1/0/7] quit
[SwitchA] interface ten-gigabitethernet 1/0/8
[SwitchA-Ten-GigabitEthernet1/0/8] port link-aggregation group 1
[SwitchA-Ten-GigabitEthernet1/0/8] quit
# Configure Layer 2 aggregate interface 1 as a trunk port, and assign the aggregate interface to
VLAN 4001.
[SwitchA] interface bridge-aggregation 1
[SwitchA-Bridge-Aggregation1] port link-type trunk
[SwitchA-Bridge-Aggregation1] port trunk permit vlan 4001
[SwitchA-Bridge-Aggregation1] quit
# Create Layer 2 aggregate interface 2, and configure it to operate in dynamic aggregation
mode.
[SwitchA] interface bridge-aggregation 2
[SwitchA-Bridge-Aggregation2] link-aggregation mode dynamic
# Disable STP on Layer 2 aggregate interface 2.
[SwitchA-Bridge-Aggregation2] undo stp enable
[SwitchA-Bridge-Aggregation2] quit
# Assign ports Ten-GigabitEthernet 2/0/5 through Ten-GigabitEthernet 2/0/8 to Layer 2
aggregation group 2.
[SwitchA] interface ten-gigabitethernet 2/0/5
[SwitchA-Ten-GigabitEthernet2/0/5] port link-aggregation group 2
[SwitchA-Ten-GigabitEthernet2/0/5] quit
[SwitchA] interface ten-gigabitethernet 2/0/6
[SwitchA-Ten-GigabitEthernet2/0/6] port link-aggregation group 2
[SwitchA-Ten-GigabitEthernet2/0/6] quit
[SwitchA] interface ten-gigabitethernet 2/0/7
[SwitchA-Ten-GigabitEthernet2/0/7] port link-aggregation group 2
[SwitchA-Ten-GigabitEthernet2/0/7] quit
[SwitchA] interface ten-gigabitethernet 2/0/8
[SwitchA-Ten-GigabitEthernet2/0/8] port link-aggregation group 2
[SwitchA-Ten-GigabitEthernet2/0/8] quit
# Configure Layer 2 aggregate interface 2 as a trunk port, and assign the aggregate interface to
VLAN 4002.
[SwitchA] interface bridge-aggregation 2
[SwitchA-Bridge-Aggregation2] port link-type trunk
[SwitchA-Bridge-Aggregation2] port trunk permit vlan 4002
[SwitchA-Bridge-Aggregation2] quit
# Create Layer 2 aggregate interface 3, and configure it to operate in dynamic aggregation
mode.
[SwitchA] interface bridge-aggregation 3
[SwitchA-Bridge-Aggregation3] link-aggregation mode dynamic
# Enable STP on Layer 2 aggregate interface 3.
[SwitchA-Bridge-Aggregation3] stp enable
# Enable LACP MAD for Layer 2 aggregate interface 3.
[SwitchA-Bridge-Aggregation3] mad enable
You need to assign a domain ID (range: 0-4294967295)
[Current domain is: 1]:

Table of Contents

Other manuals for HP FlexFabric 5700 series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP FlexFabric 5700 series and is the answer not in the manual?

HP FlexFabric 5700 series Specifications

General IconGeneral
Layer SupportL2/L3
Routing ProtocolOSPF, BGP, RIP, IS-IS, Static Routing
Remote Management ProtocolSNMP, CLI, Web
FeaturesVXLAN
Compliant StandardsIEEE 802.1D, 802.1Q, 802.1w, 802.1s, 802.3ad
Operating Temperature0°C to 45°C
Operating Humidity10% to 90% (non-condensing)
VLANs4K

Related product manuals