To Next Page

To Previous Page

ENWW Using the Embedded Web Server 121

Primary WINS

Server

Specifies the IP address of the primary Windows Internet Naming

Service (WINS) server. The WINS server provides IP address

and name resolution services for network computers and devices.

Secondary WINS

Server

Specifies the IP Address to be used for WINS if the primary WINS

Server is unavailable.

Syslog Server Specifies the IP address of a host computer that is configured to

receive syslog messages from the HP Jetdirect print server. If a

Syslog Server is not specified, syslog messages are disabled.

For more information, see Appendix A

Syslog Maximum

Messages

Specifies the maximum number of syslog messages that can be

sent by the HP Jetdirect print server on a per-minute basis. This

setting allows administrators to control the log file size. The

default is 10 per minute. If set to zero, no maximum number is

defined.

Syslog Priority Controls the filtering of syslog messages that are sent to the

syslog server. The filter range is 0 to 8, with 0 being the most

specific and 8 being the most general. Only messages that are

lower than the filter level specified (that is, higher in priority) are

reported. The default value is 8 which reports all syslog

messages. A value of zero effectively disables syslog reporting.

Idle Timeout Specifies the number of seconds that an idle connection is

allowed to remain open. Up to 3600 seconds can be set. 270 is

the default value. If set to 0, the timeout is disabled and TCP/IP

connections will remain open until closed by the device at the

other end of the network (for example, a workstation).

TTL/SLP Specifies the IP multicast Time To Live (TTL) discovery setting

for Service Location Protocol (SLP) packets. The default value is

4 hops (the number of routers from the local network). The range

is 1-15. If set to -1, multicast capability is disabled.

For print servers configured for Auto IP (link-local) addresses, this

field will be ignored. TTL on outbound packets will always be set

to 255 and limited to the link-local network.

Table 4.4 TCP/IP Settings (2 of 3)

Item Description

Questions and Answers:

Need help?

Do you have a question about the HP jetdirect 175x and is the answer not in the manual?

HP jetdirect 175x Specifications

General

Network ready	Yes
Power supply type	AC/DC
Cabling technology	10/100Base-T(X)
Networking features	Fast Ethernet
Compatible operating systems	Windows 98 Windows NT 4.0 Windows Me Windows 2000 Windows Server 2003 Windows XP (32/64-bit) Windows Vista (32/64-bit) Windows 2003 (64-bit) Mac OS 8.6+
Product color	White
Firmware upgradeable	No
Number of simultaneous printers	1
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 55 °C
Operating relative humidity (H-H)	15 - 95 %
Safety	IEC
Certification	FCC, DoC
AC input voltage	100-127 V
AC input frequency	60 Hz
Power consumption (typical)	2.8 W
Supported network protocols	TCP/IP, IPX/SPX, AppleTalk, IP Direct, LPD, Telnet, SLP, IGMP, BOOTP/DHCP, WINS, SNMP, HTTP, Auto-IP, Bonjour
Flash memory	2 MB
Minimum storage drive space	40 MB
Minimum system requirements	CD-ROM
Networking standards	IEEE 802.3, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s
Network connection type	Ethernet LAN
Copper ethernet cabling technology	100BASE-T, 100BASE-TX, 10BASE-T
USB connector type	USB Type-A
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Parallel ports quantity	0
Cables included	USB