HP jetdirect 175x User Manual

ENWW HP Jetdirect Configuration Page 242
62 DEFAULT IP
CONFIGURED
An IP address could not be retrieved over the network.
The print server will default to a legacy default IP address
192.0.0.192.
63 AUTO IP IN
PROGRESS
The print server is automatically assigning an IP address
using link-local addressing in the form 169.254.x.x.
64 INVALID
PASSWORD
An invalid password was specified through TFTP. Verify that
the password consists of a maximum of 16 printable
characters.
83 DISCONNECTING
FROM SERVER
The server has been shut down because of a configuration
change or reset request. This message automatically clears
after a few seconds, unless the printer is offline, is in an error
state, or is servicing another I/O port or another network
protocol.
84 DHCP LEASE
TIMERS ADJUSTED
The print server detected a DHCP lease error due to one of
the following conditions:
● Renew time is less than 30 seconds.
● Rebind time is less than 52 seconds.
● Rebind time is less than, or equal to, the Renew time.
● The lease duration is less than, or equal to,
the Rebind time.
86 FOR
MULTILANGUAGES
UPGRADE AGAIN
When upgrading a supported print server that contains a
firmware version prior to X.24.00, it will be necessary to
perform the firmware upgrade again if you want the print
server to support management tools (for example, the
embedded Web server) using non-English languages.
F1 TRYING TO
CONNECT TO
SERVER
The HP Jetdirect print server is trying to connect to the
NetWare server(s). This is a normal message. Wait until
either the connection is established or another status
message appears.
F2 TFTP IN
PROGRESS
The print server is attempting to use TFTP to obtain TCP/IP
configuration settings over the network.
F3 BOOTP/RARP IN
PROGRESS
The print server is attempting to use BootP or RARP to
obtain TCP/IP configuration settings over the network.
F4 BOOTP/DHCP IN
PROGRESS
The print server is attempting to use BootP or DHCP to
obtain TCP/IP configuration settings over the network.
Table 9.12 Error Messages (11 of 11)
Error Code and
Message
Description

HP jetdirect 175x Specifications

General

Network ready	Yes
Power supply type	AC/DC
Cabling technology	10/100Base-T(X)
Networking features	Fast Ethernet
Compatible operating systems	Windows 98 Windows NT 4.0 Windows Me Windows 2000 Windows Server 2003 Windows XP (32/64-bit) Windows Vista (32/64-bit) Windows 2003 (64-bit) Mac OS 8.6+
Product color	White
Firmware upgradeable	No
Number of simultaneous printers	1
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 55 °C
Operating relative humidity (H-H)	15 - 95 %
Safety	IEC
Certification	FCC, DoC
AC input voltage	100-127 V
AC input frequency	60 Hz
Power consumption (typical)	2.8 W
Supported network protocols	TCP/IP, IPX/SPX, AppleTalk, IP Direct, LPD, Telnet, SLP, IGMP, BOOTP/DHCP, WINS, SNMP, HTTP, Auto-IP, Bonjour
Flash memory	2 MB
Minimum storage drive space	40 MB
Minimum system requirements	CD-ROM
Networking standards	IEEE 802.3, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s
Network connection type	Ethernet LAN
Copper ethernet cabling technology	100BASE-T, 100BASE-TX, 10BASE-T
USB connector type	USB Type-A
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Parallel ports quantity	0
Cables included	USB

Weight and Dimensions

Depth	127 mm
Width	101.6 mm
Height	38.1 mm
Weight	118 g