IBM 9306

To Next Page

To Previous Page

Rear panel

Note: Make sure empty NetBAY3 enclosures (no devices installed) have the rear

cover securely attached.

NetBAY3 enclosure 75

Main Page

Table of Contents5
About this Manual9
Important Safety Information9
Online Support9
General Checkout11
Power Checkout12
Powering off the Rack13
Type 9306 Model 250/420/42115
Features15
Netbay 42 and Netbay 25 Cabinets15
Installing a Rack Cabinet16
Part Listing (Type 9306)38
Type 9306 Models 200/900/91041
Type 9306 Models 900/91041
Features41
Locations41
Side Panel41
Parts Listing (Type 9306 Model 200)42
Type 9306 Model 900/91044
Features44
Locations44
Parts Listing (Type 9306 Model 900/910)48
Type 9306 Models 4QS, 4QX, 9QS, 9QX, 9TS, 9TX51
Features51
IBM PC Server Expansion Rack Models51
Locations51
Server Selector Console51
Server Selector Unit52
Connections53
Power Distribution Unit53
Cooling Fan54
Sliding Trays55
Sliding Rails56
Keyboard Tray57
Parts Listing (Type 9306 - 19-Inch) Models 9QS, 9TS and 9QX, 9TX58
Parts Listing (Type 9306 - 24-Inch) Models 4QS, 4QX61
Netbay 42 Enterprise Rack (Type 9308 Models 42P, 42X, 4SA, 4SB, 42S, 42E)65
Features65
Locations69
Removing and Installing Panels69
Doors71
Removing and Installing the Top 6U Portion of the Rack75
Installing the Stabilizer Bracket76
Attaching Rack Cabinets in a Suite76
Installing L-Channel Support Rails to Rack Mounting Brackets78
Parts Listing (Type 9308 Model 42P, 42X)81
Netbay3 Enclosure83
Features83
Locations83
Casters83
Foot Pads84
Front Cover84
Rear Panel85
Device Side Rails86
Stacking Netbay3 Enclosures86
Parts Listing (Netbay3)88
Netbay3E Enclosure89
Features89
Locations89
Casters89
Front Cover90
Rear Panel91
Device Side Rails91
Stacking Netbay3E Enclosures91
Parts Listing (Netbay3E)93
1U Flat Panel Monitor Console Kit95
Installing the Flat Panel Monitor Console Kit97
Installing the Flat Panel Monitor and Keyboard Tray97
Installing an Optional Console Switch105
Installing Optional Devices111
Installing Devices on the Rack Cabinet Mounting Flanges112
Installing Threaded Rails or Bars114
Installing Cage Nuts114
Using the Cage-Nut-Insertion Tool114
Using a Flat-Blade Screwdriver115
Clip Nuts115
Installing an Uninterruptible Power Supply116
Installing a Power Distribution Unit118
Power Distribution Unit119
Installing a PDU Vertically120
Installing a PDU Horizontally121
Installing a Server121
Installing a Large Server122
Installing a Small Server122
Installing a Storage Expansion Unit124
Installing a Fibre Channel RAID Controller Unit125
Installing a Fibre Channel Hub125
Installing an SP Switch126
Installing a Fixed Shelf127
Installing a Keyboard Tray129
Installing a Flat Panel Monitor Rack Mount Kit129
Installing a Monitor Shelf130
IBM Netbay Console Switch131
Features133
Tool Requirements134
Specifications134
Installation Overview135
Installing a Console Switch Vertically in a Rack135
Installing a Console Switch Horizontally in a Rack138
Parts Listing (Netbay Console Switch)140
Netbay Power Distribution Units140
Netbay Rack Power Distribution Unit Introduction140
Tool Requirements141
Installation Overview141
Installing Devices Vertically142
Installing a Single Device Horizontally143
Installing Two Devices Horizontally145
Cabling Your Pdus147
Netbay Front-End Power Distribution Unit Introduction155
Tool Requirements156
Installation Overview156
Installing a Single Device Vertically156
Installing Two Devices Vertically159
Rack PDU Specifications164
Line Cords165
Power Cables165
Netbay Server Dual-Cord Power Distribution Unit Introduction165
Tool Requirements166
Installation Overview166
Installing Devices Vertically166
Installing a Single Device Horizontally168
Installing Two Devices Horizontally170
Cabling Your Pdus172
Power Cables179
Line Cords180
Parts Listing (Power Distribution Units)180
Selector Switch Locations180
Selector Switch Cable Connections182
Tiered Switch Configuration182
Selector Switch Environment183
Resetting the Selector Switch183
Blank Bezel184
Fixed Shelf184
Keyboard Tray185
Removing the Existing Flat Panel Monitor Stand185
Installing the New Monitor Stand186
Starting the System191
Configuring the Selector Switch192
Switching Among Servers192
Advanced Selector Switch Functions193
Scanning the Servers193
Displaying Version Information and Device Settings193
Saving Hardware Configuration194
Resetting the Mouse and Keyboard194
Setting a Scan Pattern194
Assigning Unique Names to Servers195
Changing Menu Attributes196
Changing the Status Flag Attributes197
Assigning Specific Device Types198
Making Connections under Power199
Related Service Information201
Safety Information201
Safety Notices (Multilingual Translations)208
Safety Inspection Guide239
Handling Electrostatic Discharge-Sensitive Devices240

Table of Contents

Related product manuals