• METER AND SQUELCH ADJUSTMENT (CONTINUED)
DISPLAY
ADJUSTMENT ADJUSTMENT CONDITIONS
MAIN
BAND
SUB BAND 17
• Set an SSG output level as:
FM
S-METER
0.45IJ,V"
(-114
dBm)
5'
r
a
_,
L'
18
• Set
an
SSG output level as:
FM
3.2
IJ,V"
(-
97 dBm)
5'
r
_,
L'
9
19 • Set an SSG output level as:
FM
32
IJ,V"
(-77
dBm)
5'
r
_,
L'
sa
SUB BAND 20
• Set
an SSG output level as:
FM
NOISE SOL
0.063IJ,V"
(-131
dBm)
na
15E5
21
• Set an SSG output level
as:
FM
0.2
IJ,V"
(-121
dBm)
na
15Et:
SUB BNAD 22
• Set an SSG output level as:
FM
[Ent:E,-
"This output level of standard signal generator (SSG) is indicated as SSG's open circuit.
5-7
RF
METER ADJUSTMENT
• ADJUSTMENT
1
1
DISPLAY
ADJUSTMENT
ADJUSTMENT
CONDITIONS
MAIN
BAND
ENTERING
•
Connect a terninator
to
the [REMOTE]
ADJUSTMENT connector on the rear
panel.
SET MODE • While
pushing the [CALL] switch, turn
5[Rn
power ON.
RF METER 1
• Connect an RF meter
to
the [VHF ANT]
connector.
FM
VFOA
• [RF PWR]
: Max.
level
1'-15.
120.0
,
,
• Transmitting
5-8 METER REFERENCE ADJUSTMENT
OPERATION
SUB
BAND
Push [CALL].
FM
• Verify
"SO"
on the
/'-{s.oeao
11
bar-meter.
Push [CALL].
FM
• Verify "S9" on the
/'-{s.oeao
18
bar-meter.
Push [CALL].
FM
• Verify "S60" on the
/'-{S.02CLO
1'3
bar-meter.
FM
Push [CALL].
/'-{S.02CLO
c'a
FM
Push [CALL].
/'-{S.Oc'aO
c'
I
FM
-
Push [CALL].
/'-{S.OeCLO
c'2
OPERATION
SUB
BAND
Push [DOWN] to enter RF
meter set mode.
d,.,
uP
00
Push [CALL]
FM
• Verify "80
%"
(S9+40) on
,_,e
:='0
30
the analog RF meter.
NOTE: This adjustment is not necessary unless the CPU or EEPROM ICs are replaced. The set data would not be cleared by CPU resetting.
• ADJUSTMENT
DISPLAY
ADJUSTMENT ADJUSTMENT CONDITIONS
OPERATION
MAIN
BAND
SUB BAND
ENTERING
•
Connect a terminator
to
the [REMOTE]
!
Push [SCAN]
to
enter meter
ADJUSTMENT connector on the rear
panel.
5[Rn
reference set mode. Once
SET MODE
• While
pushing the [CALL] switch, turn
d,.,
uP
00
entering mode, use [UP] /
power
ON.
[DOWN]
switch
to
select item.
IF SHIFT 1
• Set the [IF SHIFT] and [RIT] to center
Push [CALL].
CENTER position.
[EntEr
Rrr:
51-1
1Ft
2'/
POSITION
METER 2
• Set the analog meter indication
to
"S
1"
f'/E
tE,
Push [CALL].
INDICATION by the [DIAL].
51
C,
,
25
,
3
• Set the analog meter indication
to
"S9"
f'/E
tE,
Push [CALL].
by the
[DIAL].
5/C,
9
26
4
• Set the analog meter indication
to
I'IE
tE,
Push [CALL].
"S9+20" by the [DIAL].
51
C,
,:'[1
21
5
• Set the analog meter indication
to
I'IE
tE,
Push [CALL].
"S9+60" by the [DIAL].
51
C,
GO
2B
5
-13
To Next Page
Loading...
