InFocus IN3916 User Manual

16
Shutting down the projector
Screen Save Time
You can make the black screen appear after a preset number of minutes by turning
on the Screen Save Time feature in the Setup menu. See page 33.
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction with the
projector is performed for 30 minutes. By default, this feature is off. You can
change the length of time, see page 33.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad. The lamp
turns off and the LED blinks amber for 1 minute while the fans continue to run to
cool the lamp. When the lamp has cooled, the LED lights amber and the fans stop.
Unplug the power cable to completely power off the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does not,
troubleshoot the setup.
The Status Indicator Panel on top of the projec
tor i
ndicates the state of the projector
and can help you troubleshoot.
Table 2: Status indicator light behavior and meaning
Icon Meaning
Power, solid amber
Power, blinking green
Power, solid green
Power, blinking amber
The projector is plugged in.
The power button has been pressed and the
software
is initializing.
The projector
is on and initialized.
The power button has been pressed to turn
the pr
ojector
off and the fans are running
to cool the projector.
Thermometer
The projector is too hot. Make sure the
vents aren’t blocked (see page 22). Turn
off the projector and wait one minute, then
turn
the projector on again. Contact
Technical Support if the problem persists.
Visit www.infocus.com/support to contact
service.
Lamp
Turn off the projector and wait one minute,
then turn the projector on again. If the
lamp light turns on again, replace the lamp
and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one minute,
then turn the projector on again. If the
service lamp turns on again, service is
required. Visit www.infocus.com/support
to contact service.

InFocus IN3916 Specifications

General

Projection distance	0.75 - 1.65 m
Vertical scan range	23.5 - 85 Hz
Horizontal scan range	31.4 - 91.1 kHz
Projection technology	DLP
Contrast ratio (typical)	3200:1
Screen size compatibility	1.44 - 3.17 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	± 30 °
Resolution	1920 x 1200 pixels
Aspect ratio	16:10
RS-232 ports	1
Weight (imperial)	9.9 lbs
Dimensions (WxDxH)	320 x 251.5 x 127 mm
Power requirements	90-264V, 50/60Hz
Connectivity technology	Wired
Focal length range	- mm
Lamp power	220 W
Light source type	Lamp
Service life of light source	2500 h
Service life of light source (economic mode)	4000 h
HD-Ready	Yes
Analog signal format system	NTSC, PAL, SECAM
RMS rated power	10 W
Number of built-in speakers	2
DVI port	No
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
S-Video inputs quantity	0
VGA (D-Sub) ports quantity	3
Noise level	35 dB
Certification	UL, c-UL, FCC, CE, C-Tick Mark, NOM, COFETEL
Power source	AC
Power consumption (standby)	- W
Power consumption (typical)	238 W
Operating temperature (T-T)	5 - 40 °C
Product type	Standard throw projector

Weight and Dimensions

Weight	4490 g
Package weight	6580 g