InFocus IN3916 User Manual

38
Displaying PtG presentations
Follow these steps to show a slideshow presentation using Presentation-to-Go (PtG)
presentation. This will preserve most PowerPoint embedded videos, transition
effects, and animations. (Note: these instructions apply to PowerPoint 2007 in
Windows; for other presentation programs refer to the presentation program's
instructions or help file for the steps needed to save a presentation as separate JPEG
files.)
To convert a PowerPoint presentation to
a PtG presentation:
1 Download and install the PtG Converter software onto your computer (avail-
able on www.infocus.com/support).
2 Close all open computer applications.
3 Open the PtG Converter Lite program and click the Convert button.
4 Navigate to the desired PowerPoint presentation and click OK to begin conver-
sion.
5 When the conversion is complete, a “Conversion Complete” message will dis-
play. Click OK.
To display the PtG presentation:
1 Connect a USB flash drive to your computer and copy PtG presentation from
your computer to the USB flash drive.
2 Turn on your projector if needed.
3 Remove the USB flash drive from your computer and plug it into the USB A
connector on the rear of the projector.
4 The projector will display the LitePort menu.
5 Click PtG and navigate to the desired presentation using the arrow buttons on
the projector keypad or remote.
6 Click Select to display the desired presentation.
7 Use the arrow buttons to navigate through the presentation.
To stop displaying the presentation: cl
ick the Menu button.
Troubleshooting LitePort
• If images load slowly: Make sure you are using a newer USB 2.0-
compatible (high speed) USB flash drive. Larger image file sizes may also
slow down the player; to reduce file size, use an image editing program on
your computer to resize images smaller; for the best balance between image
quality and speed, resize images to be 1024 pixels wide.
• If no images are found, or some images are not shown, or you only see folder
thumbnails but no images: Make sure that images are JPEG file type (file
extensions .JPEG and .JPG); other file types are not supported and will be
ignored.
• Using the Source button, make sure you have the LitePort source selected and
make sure your USB flash drive is correctly and completely plugged in to the
projectors LitePort connector.
• If nothing happens when you connect your USB flash drive, and you cannot
select the LitePort input source as described above: Check the format of your
USB storage device. LitePort only supports USB storage devices formatted as
FAT32. Devices formatted as NTFS, and non-storage devices (such as
cameras) are not supported.

InFocus IN3916 Specifications

General

Projection distance	0.75 - 1.65 m
Vertical scan range	23.5 - 85 Hz
Horizontal scan range	31.4 - 91.1 kHz
Projection technology	DLP
Contrast ratio (typical)	3200:1
Screen size compatibility	1.44 - 3.17 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	± 30 °
Resolution	1920 x 1200 pixels
Aspect ratio	16:10
RS-232 ports	1
Weight (imperial)	9.9 lbs
Dimensions (WxDxH)	320 x 251.5 x 127 mm
Power requirements	90-264V, 50/60Hz
Connectivity technology	Wired
Focal length range	- mm
Lamp power	220 W
Light source type	Lamp
Service life of light source	2500 h
Service life of light source (economic mode)	4000 h
HD-Ready	Yes
Analog signal format system	NTSC, PAL, SECAM
RMS rated power	10 W
Number of built-in speakers	2
DVI port	No
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
S-Video inputs quantity	0
VGA (D-Sub) ports quantity	3
Noise level	35 dB
Certification	UL, c-UL, FCC, CE, C-Tick Mark, NOM, COFETEL
Power source	AC
Power consumption (standby)	- W
Power consumption (typical)	238 W
Operating temperature (T-T)	5 - 40 °C
Product type	Standard throw projector

Weight and Dimensions

Weight	4490 g
Package weight	6580 g