What to do if Inovance Aonarch MD500L DC Drives show Err02 error?
If your Inovance DC Drive shows Err02 during acceleration, it means there's an overcurrent issue. This could be due to several reasons: * A short circuit in the output circuit. If this is the case, eliminate the short circuit. * The power supply might be too low. Check the power supply to ensure it's normal. * A sudden load was added during acceleration. Remove the added load.
What to do if Inovance Aonarch MD500L show Err06 error?
If your Inovance DC Drive displays Err06 during deceleration, it indicates an overvoltage issue. This can happen because: * An external force is driving the motor. To resolve this, cancel the external force or install a braking resistor. * The deceleration time is too short. Try increasing the deceleration time. * The braking resistor is not installed. Install the braking resistor.
What to do if Inovance Aonarch MD500L DC Drives show Err05 error?
If your Inovance DC Drive displays Err05 during acceleration, it indicates an overvoltage issue. This can happen because: * An external force is driving the motor. To resolve this, cancel the external force or install a braking resistor. * The acceleration time is too short. Try increasing the acceleration time. * The braking resistor is not installed. Install the braking resistor.
General| Operating Temperature | -10°C to +50°C |
|---|---|
| Storage Temperature | -20°C to +60°C |
| Cooling Method | Forced air cooling |
| Enclosure Rating | IP20 |
| Product Series | MD500L Series |
| Input Voltage | 380V to 480V AC |
| Output Voltage | 0V to Input Voltage |
| Control Mode | V/F control |
| Control Method | PWM |
| Overload Capacity | 150% rated current for 60 seconds |
| Protection Features | Overcurrent, overvoltage, undervoltage, overheat, short circuit |
| Communication Interfaces | RS485, Modbus, CANopen |
| Ambient Humidity | 5% to 95% (non-condensing) |
| Altitude | Below 1000m without derating |
Guidance for first-time users of the MD500L Series AC Drive.
Guidelines for qualified personnel on setting drive parameters for optimal performance.
Essential safety information and precautions for operating the AC drive.
Explains safety levels (DANGER, WARNING, CAUTION) and their meanings.
Instructions and precautions for safely unpacking the AC drive.
Guidelines for safe storage and transportation of the AC drive.
Safety warnings and general requirements for installing the AC drive.
Safety precautions related to wiring the AC drive, including DANGER warnings.
Safety instructions and precautions to be followed before and during the power-on sequence.
Safety precautions and warnings for operating the AC drive.
Safety warnings and procedures for performing maintenance on the AC drive.
Safety guidelines for inspecting and repairing the AC drive.
Guidelines for safely disposing of or recycling the AC drive.
Explains common safety signs used on the equipment and their meanings.
Details on certifications and standards the AC drive complies with.
Explains how to identify the AC drive's model and information on its nameplate.
Identifies and describes the main physical parts of the AC drive.
Provides detailed technical specifications and data for the AC drive models.
Shows mounting dimensions and weight specifications for different drive models.
Details on the physical installation of the AC drive.
Specifies environmental requirements for installing the AC drive.
Instructions for mounting the AC drive using a backplate.
Illustrates a typical wiring diagram for frequency reference using multi-reference input.
Illustrates a typical wiring diagram for frequency reference using analog input.
Details the terminal arrangement and function for the main power circuit.
Describes the terminal arrangement and function for control circuits.
Details the outline, dimensions, and terminals of the I/O extension board.
Overview of the LED operating panel functions and options.
Explains the function of each key on the AC drive's operating panel.
Describes the status and meaning of the indicators on the operating panel.
Timing diagram illustrating normal travel operation with multi-reference input.
Guides for tuning elevator performance based on symptoms and diagnostics.
Step-by-step flowchart for setting up the AC drive.
Explains the IGBT Enable function for safe motor control with output contactors.
Details on setting up the UPS/ARD mode for rescue operations during power failure.
Lists common fault codes, their possible causes, and solutions.
Addresses common drive symptoms and provides troubleshooting solutions.
Daily checks and maintenance tasks to ensure normal operation and prevent damage.
Periodic inspection points for the AC drive and its components.
Information on parts that wear out and their service life.
Details the service life of components like fans and capacitors.
Step-by-step instructions for removing and replacing cooling fans.
Guidelines for proper storage of the AC drive to maintain its condition.
Lists fundamental parameters for the AC drive.
Parameters related to motor configuration and settings.
Parameters specific to vector control mode.
Parameters specific to V/F control mode.
Parameters related to configuring digital and analog inputs.
Parameters for configuring digital and relay outputs.
Parameters for managing the start and stop sequences of the drive.
Displays product and software version information.
Parameters for auxiliary functions like braking and UPS operation.
Parameters related to fault detection and protection mechanisms.
Parameters for setting up multiple reference sources.
General drive parameters not covered in other groups.
Parameters for managing user settings and backups.
Parameters for optimizing drive control performance.
Parameters for monitoring various drive states and values.
To Next Page