Inovance IS580 Series - Page 145

U
V
Ｗ
PG card
(MD38PG4)
CNR1
Interface of external
operation panel
OP
+24V
DI1
DI2
DI3
DI4
DI5
COM
AI1
AI2
GND
Pressure reference 1: 0 to 10 V
Flow reference 1: 0 to 10 V
+13V
AI3
GND
(Pressure sensor signal)
GND
V+
OUTPUT
PTC-P-1
PTC-N-1
Thermistor (PTC×××)
CANH CGND
CANL
485B 485A
Pump enable
PID selection 1
Fault reset
CAN communication
enabled
(Motor overheat
protection terminal)
EXC
/EXC
SIN
SINLO
COS
PTC-P-2 (Standby)
PTC-N-2 (Standby)
Vacant
COSLO
PTC-P
PTC-
N
PTC-P
PTC-N
U
V
W
L1
L2
L3
EXC
/
EXC
SIN
SINLO
COS
COSLO
Red-white
Yellow-white
Yellow
Blue
Red
Black
The colored cable
corresponds to the
resolver of Tama
River
Model:
TS
2640N321E
64
Connect the
thermistor to
the position
transducer
location on the
computer.
Loop magnetic ring (wind it a turn.)
(Shield)
(Shield)
(Connector metal housing)
(Generally, connect the motor
thermistor to PTC-P-1 and PTC-N-1).
System computer
GND
Ferrite magnetic ring (wind it two
turns in the same direction.)
Ferrite magnetic ring (wind it two
turns in the same direction.)
AO1
AO2
GND
T/A1
T/B1
T/C1
T/A2
T/C2
T/A3
T/C3
(RELAY1: Fault output)
(RELAY3: Pressure
control state output)
(RELAY2: Slave alarm output)
1
2
3
4
5
6
7
8
9
SENSOR
R
S
T
R
S
T
Filter
MC
MCCB
Loop magnetic ring
(wind it a turn.)
L1
L2
L3
PE
L1
L2
L3
PE
(Shield)
(Shield)
(Shield)
Wiring of main circuit and control terminals:
(Wiring of the braking circuit)
(STP cable)
(STP cable)
Ferrite magnetic ring (wind it two
turns in the same direction.)
Ferrite magnetic ring (wind it two
turns in the same direction.)
Ferrite magnetic ring (wind it two
turns in the same direction.)
U
V
Ｗ
PG card
(MD38PG4)
CNR1
Interface of external
operation panel
OP
+24V
DI1
DI2
DI3
DI4
DI5
COM
AI1
AI
2
GND
PTC-P-1
PTC-N-1
Thermistor (PTC×××)
CANH CGND
CANL
485B 485A
(Motor overheat
protection terminal)
EXC
/
EXC
SIN
SINLO
COS
PTC-P-2 (Standby)
PTC-N-2 (Standby)
Vacant
COSLO
PTC-P
PTC-N
PTC-P
PTC-N
U
V
W
L1
L2
L3
EXC
/EXC
SIN
SINLO
COS
COSLO
Red-
white
Yellow-white
Yellow
Blue
Red
Black
The colored cable
corresponds to the
resolver of Tama
River
Model:
TS2640N321E64
Connect the
thermistor to
the position
transducer
location on the
computer.
Loop magnetic ring (wind it a turn.)
(Shield)
(Shield)
(Connector metal housing)
(Generally, connect the motor
thermistor to PTC-P-1 and PTC-N-1).
AO1
AO2
GND
T/A1
T/B1
T/C1
T/A2
T/C2
T/A3
T/C3
1
2
3
4
5
6
7
8
9
R
S
T
R
S
T
Filter
MC
MCCB
Loop magnetic ring
(wind it a turn.)
L
1
L2
L3
PE
L1
L
2
L3
PE
(Shield)
(Wiring of braking circuit)
(STP cable)
(STP cable)
Ferrite magnetic ring (wind it
two turns in the same direction.)
Master drive Slave drive
CAN communication enabled
Note:
In the multi-pump mode 1, only when the DI terminal set for the 50# function of both master pump and slave pump close, the multi-pump convergent ow control can be enabled.