MD280 User Manual Description of Function Codes
- 103 -
Function Code Parameter Name Setting Range Default
F0-13
Acceleration/Deceleration
time base frequency
0D[LPXPIUHTXHQF\)
1: Set frequency
0
When this parameter is set to 0, the acceleration/deceleration time indicates the time for the
$&GULYHWRLQFUHDVHIURP+]WRWKHPD[LPXPIUHTXHQF\VHWLQ)RUGHFUHDVHIURPWKH
PD[LPXPIUHTXHQF\VHWLQ)WR+]
If this parameter is set to 1, the acceleration/deceleration time indicates the time for the AC
drive to increase from 0 Hz to the set frequency or decrease from the set frequency to 0 Hz.
Function Code Parameter Name Setting Range Default
F0-14
Base frequency for UP/DOWN
PRGL¿FDWLRQGXULQJUXQQLQJ
0: Running frequency
1: Set frequency
0
This parameter is valid only when the frequency source is digital setting.
,WLVXVHGWRVHW WKHEDVHIUHTXHQF\WREHPRGL¿HGE\XVLQJNH\V
and or the
terminal UP/DOWN function.
Function Code Parameter Name Setting Range Default
F0-15
$X[LOLDU\
frequency source
Y selection
'LJLWDOVHWWLQJ83'2:1PRGL¿FDWLRQ
1: AI1
2: AI2
3XOVHVHWWLQJ',
4: Multi-reference
5: Simple PLC
6: PID
$,$,
8: Communication setting
0
:KHQXVHGDVDQLQGHSHQGHQW IUHTXHQF\LQSXWFKDQQHOIUHTXHQF\VRXUFHVZLWFKHG
RYHUIURP;WR<WKH DX[LOLDU\IUHTXHQF\VRXUFH<LVXVHGLQWKHVDPH ZD\DVWKHPDLQ
IUHTXHQF\VRXUFH;UHIHUWR)
:KHQWKHDX[LOLDU\IUHTXHQF\VRXUFHLVXVHGIRUVXSHUSRVLWLRQIUHTXHQF\VRXUFHLV;DQG<
VXSHUSRVLWLRQRU;VZLWFKHGRYHUWR;DQG<VXSHUSRVLWLRQSD\DWWHQWLRQWRWKHIROORZLQJ
aspects:
1. ,IWKHDX[LOLDU\IUHTXHQF\VRXUFH<LVGLJLWDOVHWWLQJWKHSUHVHWIUHTXHQF\ )GRHV
not take effect. You can directly adjust the set main frequency by pressing keys
and
RQWKHRSHUDWLRQSDQHORUXVLQJWKHWHUPLQDO83'2:1IXQFWLRQ
2. ,IWKHDX[LOLDU\IUHTXHQF\VRXUFHLVDQDORJLQSXW$,$,RUSXOVHVHWWLQJRIWKH
LQSXWFRUUHVSRQGVWRWKHUDQJH RIWKHDX[LOLDU\IUHTXHQF\<VHWLQ)DQG )
7KHPRGL¿FDWLRQUDQJHFDQEHVHWWR±QWRQ)WR)
,IWKHDX[LOLDU\IUHTXHQF\VRXUFHLVSXOVHVHWWLQJLWLVVLPLODUWRDQDORJLQSXW
efesotomasyon.com
To Next Page
Loading...
